Alicates para Circlip

Anteprima

Riferimento: 117/8

Thrust bearing 8 x 15 x 5 mm

Recensioni: 0

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 8 x 15 x 5...

Prezzo 14,80 €

 Aggiungi al carrello

Più

 In vendita su richiesta

Anteprima

Riferimento: 94/17

Thrust bearing 7 x 13 x 4.5 mm

Recensioni: 0

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 7 x 13 x 4.5...

Prezzo 21,80 €

 Aggiungi al carrello

Più

 In vendita su richiesta

Anteprima

Riferimento: 64/32

pinion gear 23-tooth

Recensioni: 0

Clutch pinion gearincl. flywheel and split taper collet23-toothmodule 1material: aluminiumtwin ballracedincl. clutch liningfits the glow plug motor

Prezzo 98,90 €

 Aggiungi al carrello

Più

 In vendita su richiesta

Anteprima

Riferimento: 55/3

Thrust bearing 10 x 25 x 6 mm

Recensioni: 0

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence.The dimensions of a ballrace mean:inside diameter (I.D.) x outside diameter (O.D.) x thickness.Thrust bearing 10 x 25 x 6...

Prezzo 16,90 €

 Aggiungi al carrello

Più

 In vendita su richiesta

Anteprima

Riferimento: 10/73

Five minute epoxy, 50 ml

Recensioni: 0

The more you build, the more frequently you use epoxies, whose components must be proportionately mixed. When you insert cartridges into the dispenser and press the components through the mixing nozzle the epoxy is ready for immediate use. Pack of 50 ml, pot life approx. 5 minutes

Prezzo 18,60 €

 Aggiungi al carrello

Più

 In vendita su richiesta

Anteprima

Riferimento: 99 A

6 x 10 x 2.5 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 6 x 10 x 2.5 mmpack of...

Prezzo 11,70 €

 Aggiungi al carrello

Più

 In vendita su richiesta

Anteprima

Riferimento: 94/27

7 x 13 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 7 x 13 x 3 mmpack of...

Prezzo 11,70 €

 Aggiungi al carrello

Più

 In vendita su richiesta

Anteprima

Riferimento: 40/1

4 x 9 x 4 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 4 x 9 x 4 mmpack of...

Prezzo 11,70 €

 Aggiungi al carrello

Più

 In vendita su richiesta

Anteprima

Riferimento: 11/63

Crankshaft nut socket spanner 11 mm

Recensioni: 0

If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 11 mm, for Webra; 6.2 mm thread

Prezzo 23,90 €

 Aggiungi al carrello

Più

 In vendita su richiesta

Anteprima

Riferimento: 55/5

10 x 21 x 5 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 10 x 21 x 5 mmpack of...

Prezzo 14,80 €

 Aggiungi al carrello

Più

 In vendita su richiesta

Anteprima

Riferimento: 17/23

7 x 14 x 3.5 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 7 x 14 x 3.5 mmpack of...

Prezzo 9,70 €

 Aggiungi al carrello

Più

 In vendita su richiesta

Anteprima

Riferimento: 64/19

15 x 24 x 5 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 15 x 24 x 5 mmpack of...

Prezzo 14,80 €

 Aggiungi al carrello

Più

 In vendita su richiesta

Anteprima

Riferimento: 75/1

10 x 26 x 8 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 10 x 26 x 8 mmpack of...

Prezzo 14,80 €

 Aggiungi al carrello

Più

 In vendita su richiesta

Anteprima

Riferimento: 94/3

Thrust bearing 4 x 10 x 3 mm

Recensioni: 0

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 4 x 10 x 3...

Prezzo 11,70 €

 Aggiungi al carrello

Più

 In vendita su richiesta

Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 12,80 €

 Aggiungi al carrello

Più

 In vendita su richiesta

Anteprima

Riferimento: 10/38

Penetrating oil

Recensioni: 0

When flying in moist air or rainy conditions you may find that rust starts to form on shafts. If this happens you could find that the swashplate is stuck fast the following day. A quick spray of penetrating oil will prevent oxidation getting a hold on the swashplate. Use it on the main rotor shaft and tail rotor shaft after flying; a few little squirts...

Prezzo 13,40 €

 Aggiungi al carrello

Più

 In vendita su richiesta