Marcas

Ninguna marca

Proveedores
Los productos más vendidos

Terraja M 2.5 HSS

70/20
Valoración 
Die M 2,5 HSS
46,10 €
Impuestos incluidos En venta bajo pedido
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción
Die M 2,5 HSS
Detalles del producto
70/20
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Terraja M 2.5 HSS

Terraja M 2.5 HSS

Die M 2,5 HSS
Escriba su propia reseña
16 altri prodotti della stessa categoria:

Riferimento: 11/80

Pipe bending tool

Recensioni: 0

A versatile bending tool for fuel tank pipes, dummy collective pitch sticks in the cockpit etc. The tool is useful for tubes or pushrods with a diameter of 3.0 and 3.2 mm

Prezzo 44,30 €
Più
In vendita su richiesta

Riferimento: 11/65

Soft sanding paper

Recensioni: 0

For preparing the GRP surface prior to the paintingP400dimensions: 11.5 x 15 cmPack of 5

Prezzo 9,70 €
Più
In vendita su richiesta

Riferimento: 11/60

Tubing cutter, up to 15 mm Ø

Recensioni: 0

The tubing cutter can handle aluminium, stainless steel and brass tubing up to 15 mm diameter. It can also be used to form a slight internal burr on tubing. For example if you use a tail rotor pushrod running in a PTFE sleeve in aluminium tubing, you can cut the aluminium to length at both ends with the tubing cutter, and the PTFE sleeve will not slip out.

Prezzo 33,30 €
Più
In vendita su richiesta

Riferimento: 11/34

Rotor blade allen key for M6 socket-head screws

Recensioni: 0

Rotor blades for large-scale model helicopters must be secured using screws of the appropriate size. Normally M4 bolts are employed, but here the usual size is M6. The T-handle of this M6 allen key provides plenty of torque, but you should only tighten the screws to the point where the blades can still align themselves at start-up.

Prezzo 11,70 €
Più
In vendita su richiesta

Riferimento: 107/1

Ball-link driver 5.5

Recensioni: 0

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverfor 5.5 mm socket spanner

Prezzo 8,40 €
Più
In vendita su richiesta

Riferimento: 11/86

Pushrod measuring holder

Recensioni: 0

Model helicopter building instructions always state pushrod length as measured from ball centre to ball centre.Determining this dimension using conventional measuring tools is not really much more accurate than estimating the length.Pushrod measuring holderpack of 2holders fit any standard calipers

Prezzo 14,80 €
Più
In vendita su richiesta

Riferimento: 11/260

Glazing panel shears straight

Recensioni: 0

These powerful, sharp shears simplify the task of cutting out vacuum-moulded bodywork components. Glazing panels, dummy fuel tanks etc. are easily cut out along the moulded-in lines using these special shears. We suggest not to cut out anything until you satisfy yourself with the exact dimensions. This is because GRP parts (fuselages etc.) are hand made...

Prezzo 32,30 €
Più
In vendita su richiesta

Riferimento: 11/28

Glasspaper file, flat

Recensioni: 0

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Prezzo 14,80 €
Più
In vendita su richiesta

Riferimento: 64/2

Flywheel puller

Recensioni: 0

If the flywheel of the clutch is sitting to tight on the tapper of the collet you can use this flywheel puller.For this purpose you remove the nut from the crankshaft, then put the puller on the crankshaft, and turn both socket-head cap screws equally approx. 5 mm into the thread of the flywheel; the flywheel loosens now.The length of the socket-head cap...

Prezzo 11,20 €
Più
In vendita su richiesta

Riferimento: 70/22

Die M 3.0 HSS

Recensioni: 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prezzo 37,80 €
Più
In vendita su richiesta

Riferimento: 11/36

Disc cutter set

Recensioni: 0

Disc cutter set pack of 5 normal variation Wear protective goggles!

Prezzo 6,60 €
Più
In vendita su richiesta

Riferimento: 90/10

File set with handle, six-part

Recensioni: 0

This special file set is particularly useful when you are cutting small openings, as they can be used to work on the tiniest of radii and straight edges. The rotary-action handle makes quick work of swapping individual tools. The collet can also be used to grip drills and taps of 2 to 5 mm ∅.

Prezzo 17,00 €
Più
In vendita su richiesta

Riferimento: 830/2

Extractor screw

Recensioni: 0

Extractor screwkey size 13for flywheel and split tapper collet on petrol engines

Prezzo 9,80 €
Più
In vendita su richiesta

Riferimento: 21/11

Tool case

Recensioni: 0

Tool case, complete empty, alone, including foam to cutsize approx. 275 x 230 x 83 mm

Prezzo 19,10 €
Più
In vendita su richiesta

Síganos en Facebook