- Es gibt keine Artikel mehr in Ihrem Warenkorb
- Versand kostenlos
- Gesamt 0,00 €
- Helikoptermodelle
- Trainer / Zweckhelikopter
- Mechaniken und Zubehör
- Scale-Ausbau
- Nieten
- Innenausbau
- Außenanbauteile
- Mehrblatt-Sätze
- Modellspezifisch
- Agusta AW 139 1:7
- AIRWOLF 2001 1:8
- AIRWOLF 2002/2003 1:7
- AIRWOLF 2004 1:5
- Apache 1:7
- neue 3D-Scaleartikel
- Bell 230/430 1:7
- Bell 412 1:6
- Bell 429 1:5
- Bell UH / 212 / 412 1:5
- Bell UH / 212 / 412 1:7
- EC 120
- EC 135/145 1:4
- EC 135/145 1:6
- Ecureuil 1:4
- Ecureuil 1:6
- Gazelle
- H145 T2
- JetRanger XL
- sonstige Aussenanbauten
- Lama / Alouette II 1:4
- Lama 1:5
- Lama / Alouette II 1:6
- Antrieb und Zubehör
- Transmision/Engranajes
- Rotorköpfe und Zubehör
- Heckrotor
- Rotorblätter
- Werkzeug, Klebstoffe
- Rumpfeinzelteile
- Elektronik
- Kleb- u. Schmierstoffe
- Kugellager$ Befestigung
- Fanartikel$ Nützliches
- Flugfertige Modelle ((A)RTF)
- Fundgrube
- KATALOG
- Earthmovers
- Angebote
- Neue Artikel
- Modelado 3D
Keine Marke
Stainless steel tail drive system
Política de seguridad
Política de envío
Política de devolución
Aktuell keine Kunden-Kommentare
Reference: 17
Tail rotor shaft 2 mm
The 2 mm steel tail rotor shaft has proved its worth for several decades, especially in beginners' models.Drive shaft, steel, 2.0 x 980 mm
Reference: 945/14
Stainless steel tail drive shaft ø 8 x 986 mm for Hughes Logo
Not available
Reference: 17/7
Articulated centre support
The use of an articulated centre support in helicopters with extreme high mounted tail booms (e.g. Hughes 500) helps to balance up to 30 mm vertical off-set between mechanics and tail rotor. The centre support is double ballraced and pre-assembled.
Reference: 17/13
Articulated joint tail drive system
On a model helicopter like the Hughes 500 e.g. the tail boom is extremely high connected. Therefore an articulated centre support is applied in addition to the articulated tail drive system. The centre support is double ballraced and pre-assembled.Articulated joint tail drive systemwith articulated centre support
Reference: 603/17
Adaptor 20/33, Schweizer 300 C
Component part for fuselages, Ord.No. 6030 or 6031.
Reference: 17/17
Connecting plug for 6 mm tube
Connecting plug for ø 6 mm tubePack of 2
Reference: 17/15
Stainless steel tube 6 x 890 mm
Stainless steel tube 6.0 x 0.3 x 890 mm
Reference: 17/14
Stainless steel tail drive system for 20 mm
Of course the explanation of Ord.No. 17/10 concerning a 2 mm steel drive wire in acrobatics applies not only for fuselages, it is similar for training helicopters.When you convert a trainer you use the existing tail boom. Main gearbox and tail gearbox have to be provided with a claw connector 49/12 each.Models over a certain age should be checked whether...
Reference: 17/55
Stainless steel tail drive system for 40° gear
Stainless steel drive for installationin models with 40° angle gearboxcomplete as shown
Reference: 17/16
Stainless steel tube 6.0 x 0.3 x 950 mm
Advanced pilots appreciate the more precise control response of a rigid tail rotor drive system, as provided by a stainless steel drive shaft. Stainless steel tube 6.0 x 0.3 x 950 mm
Reference: 17/18
Connecting plug for tube 5 mm
Connecting plug for stainless steel tube 5 mm pack of 2
Reference: 17/10
Stainless steel tail drive system
When a 2 mm steel drive wire is used between main gearbox and tail gearbox the tail rotor might yaw the heli during acrobatics (e.g. turn), because the wire might "wind up". At this moment a small "wind up" will cause a small change of tail rpm, which requires steering corrections.A so-called "rigid" tail drive system gives a more exact drive to the tail...
Reference: 800/9
PTFE bush guide for 0.8 mm tailboom
PTFE guides in the tail boom provide the necessary "lubrication" for the drive shaft, which eliminates the need to oil the system separately.PTFE guide for 0.8 mm tail boomPack of 3
Reference: 17/9
Centre bearing for lattice fuselage
Centre bearing for lattice fuselage Alouette II and Bell 47
Reference: 17/8
Connecting plug for tube 8 mm
Connecting plug for stainless steel tube 8 mm pack of 2
Reference: 603/18
Adaptor 20/33, Schweizer 300 C
Component part for fuselages, Ord.No. 6030 or 6031.