Inicio
Marcas

Ninguna marca

Los más vendidos
Bulon 3.5 mm - M 2.0 x 5.0 Vista rápida

Referencia: 060

Bulon 3.5 mm - M 2.0 x 5.0

Reseña(s): 0

Estos pernos de punta esférica ofrecen una conexión óptima entre un brazo de salida de servo GRP y la varilla de empuje a la mecánica. Debajo del brazo de salida, bloquea el perno de bola con una tuerca hexagonal M 2. Para brazos de salida de aluminio, utiliza pernos de punta esférica. 060/7 y fluido de bloqueo de hilo.

Precio 13,80 €
Más
En venta bajo pedido
Los productos más vendidos

Sistema de transmision de cola

17/20
Valoración 
cola de acero inoxidable de 8 mm de diametrosyste
93,80 €
Impuestos incluidos En venta bajo pedido
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción
cola de acero inoxidable de 8 mm de diametrosyste
Detalles del producto
17/20
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Sistema de transmision de cola

Sistema de transmision de cola

cola de acero inoxidable de 8 mm de diametrosyste
Escriba su propia reseña
16 autres produits dans la même catégorie :
Stainless steel tail drive... Aperçu rapide

Référence: 17/14

Stainless steel tail drive system for 20 mm

Commentaire(s): 0

Of course the explanation of Ord.No. 17/10 concerning a 2 mm steel drive wire in acrobatics applies not only for fuselages, it is similar for training helicopters.When you convert a trainer you use the existing tail boom. Main gearbox and tail gearbox have to be provided with a claw connector 49/12 each.Models over a certain age should be checked whether...

Prix 88,90 €
Détails
En vente sur demande
Stainless steel tube 6.0 x... Aperçu rapide

Référence: 17/16

Stainless steel tube 6.0 x 0.3 x 950 mm

Commentaire(s): 0

Advanced pilots appreciate the more precise control response of a rigid tail rotor drive system, as provided by a stainless steel drive shaft. Stainless steel tube 6.0 x 0.3 x 950 mm

Prix 30,00 €
Détails
En vente sur demande
Tail rotor shaft 2 mm Aperçu rapide

Référence: 17

Tail rotor shaft 2 mm

Commentaire(s): 0

The 2 mm steel tail rotor shaft has proved its worth for several decades, especially in beginners' models.Drive shaft, steel, 2.0 x 980 mm

Prix 5,60 €
Détails
En vente sur demande
Articulated joint tail... Aperçu rapide

Référence: 17/13

Articulated joint tail drive system

Commentaire(s): 0

On a model helicopter like the Hughes 500 e.g. the tail boom is extremely high connected. Therefore an articulated centre support is applied in addition to the articulated tail drive system. The centre support is double ballraced and pre-assembled.Articulated joint tail drive systemwith articulated centre support

Prix 138,60 €
Détails
En vente sur demande
Articulated centre support Aperçu rapide

Référence: 17/7

Articulated centre support

Commentaire(s): 0

The use of an articulated centre support in helicopters with extreme high mounted tail booms (e.g. Hughes 500) helps to balance up to 30 mm vertical off-set between mechanics and tail rotor. The centre support is double ballraced and pre-assembled.

Prix 67,70 €
Détails
En vente sur demande
Stainless steel tail drive... Aperçu rapide

Référence: 17/10

Stainless steel tail drive system

Commentaire(s): 0

When a 2 mm steel drive wire is used between main gearbox and tail gearbox the tail rotor might yaw the heli during acrobatics (e.g. turn), because the wire might "wind up". At this moment a small "wind up" will cause a small change of tail rpm, which requires steering corrections.A so-called "rigid" tail drive system gives a more exact drive to the tail...

Prix 73,00 €
Détails
En vente sur demande