Marcas

Ninguna marca

Referencia: 060

Bulon 3.5 mm - M 2.0 x 5.0

Reseña(s): 0

Estos pernos de punta esférica ofrecen una conexión óptima entre un brazo de salida de servo GRP y la varilla de empuje a la mecánica. Debajo del brazo de salida, bloquea el perno de bola con una tuerca hexagonal M 2. Para brazos de salida de aluminio, utiliza pernos de punta esférica. 060/7 y fluido de bloqueo de hilo.

Precio 13,80 €
Más
En venta bajo pedido
Los productos más vendidos

Tanque de aceite (largo) Lama 1:4

341/407
Valoración 

Tanque de aceite grande Lama 1: 4

106,30 €
Impuestos incluidos
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción

Tanque de aceite grande Lama 1: 4

Detalles del producto
341/407
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Tanque de aceite (largo) Lama 1:4

Tanque de aceite (largo) Lama 1:4

Tanque de aceite grande Lama 1: 4

Escriba su propia reseña
16 altri prodotti della stessa categoria:

Riferimento: 340/6

Pedana di salita per Lama

Recensioni: 0

If you have a mind to continue adding detail fittings to your Lama, you are sure to appreciate this landing gear step which can be fitted to an existing model at any time. The step is made of stainless steel, and is supplied complete with clips, screw fittings and tread material. Entry step, for Lama, pack of 1

Prezzo 56,80 €
Più
In vendita su richiesta

Riferimento: 341/509

BTP Lama 1:5

Recensioni: 0

dimensions: main part: 9.5 x 4.95 x 6.4 cm6-part

Prezzo 405,70 €
Più
In vendita su richiesta

Riferimento: 340/2

Accessori per Lama turbina

Recensioni: 0

The suckering ducts are on the model exactly on the same place as the original ones in position to the turbine on the full-size helicopter.

Prezzo 138,00 €
Più
In vendita su richiesta

Riferimento: 350/45

CESTELLO SOTTOPANCIA PER LAMA

Recensioni: 0

Great fascination is achieved by active working details on scale models, remember e.g. rotary lights and navigation lights.A working winch adds a special attraction on a model helicopter particularly if it is pivoting and fully functional!Especially on a Alouette III you hardly need fantasy, to see instead of the model the full-size helicopter in your...

Prezzo 257,30 €
Più
In vendita su richiesta

Riferimento: 341/413

Wiper, 1:4,2

Recensioni: 0

dimensions: 10.63 x 0.7 x 1.3 cmPack of 2, each 2-part

Prezzo 54,20 €
Più
In vendita su richiesta

Riferimento: 330/2

Imitazione turbina

Recensioni: 0

The dummy turbine provides the ideal starting point if you wish to install additional scale fittings on your Lama.The dummy turbine is assembled from six separate GRP mouldings, and fits all models with VR-22 mechanics installed.In the turbine-powered version of the Lama the actual turbine is located in this position.GRP dummy turbineLength approx. 490 mm

Prezzo 106,80 €
Più
In vendita su richiesta

Riferimento: 341/405

Pitot 41:4

Recensioni: 0

dimensions: 5.7 x 1.7 x 2.5 cm

Prezzo 16,30 €
Più
In vendita su richiesta

Riferimento: 340/1

Supporti ruota per Lama

Recensioni: 0

The Lama is a large helicopter, and the supplementary wheels which can be attached to the landing gear make it much easier to move the machine into and out of the hangar. However, the wheels are removed prior to flying the model. These wheel holders for our model of the Lama are made of plastic and are simply glued to the 20 mm Ø skid tubes using UHU...

Prezzo 33,50 €
Più
In vendita su richiesta

Riferimento: 1/21

Helmet for pilot William

Recensioni: 0

As you would expect, we can also supply the matching type of GRP helmet for William the Pilot; it is simply pushed into place on his head. If you wish to fit a radio headpiece, you now have plenty of scope for your imagination: a piece of foam rubber, a thin wire mount and a coiled cable are all you need to make this accessory, and the pilot will...

Prezzo 26,30 €
Più
In vendita su richiesta