Marcas

Ninguna marca

Los productos más vendidos

Bloqueo para cabeza principal

79/3
Valoración 
Inmovilizador de cabeza del rotor
16,90 €
En venta bajo pedido
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción
Inmovilizador de cabeza del rotor
Detalles del producto
79/3
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Bloqueo para cabeza principal

Bloqueo para cabeza principal

Inmovilizador de cabeza del rotor
Escriba su propia reseña
16 other products in the same category:

Reference: 11/63

Crankshaft nut socket spanner 11 mm

Review(s): 0

If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 11 mm, for Webra; 6.2 mm thread

Price 23.90€
More
On sale upon request

Reference: 11/22

Magnetiser

Review(s): 0

Everyone has experienced the annoyance of small screws which won't stay on the screwdriver. This magnetiser solves the problem. It is a small, handy unit which will magnetise any screwdriver, and the screw will then stick to it. You simply place the screwdriver in the "+" socket and move it to and from. To de-magnetise it repeat the procedure in the "-"...

Price 18.30€
More
On sale upon request

Reference: 10/38

Penetrating oil

Review(s): 0

When flying in moist air or rainy conditions you may find that rust starts to form on shafts. If this happens you could find that the swashplate is stuck fast the following day. A quick spray of penetrating oil will prevent oxidation getting a hold on the swashplate. Use it on the main rotor shaft and tail rotor shaft after flying; a few little squirts...

Price 13.40€
More
On sale upon request

Reference: 64/19

15 x 24 x 5 mm

Review(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 15 x 24 x 5 mmpack of...

Price 14.80€
More
On sale upon request

Reference: 99 A

6 x 10 x 2.5 mm

Review(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 6 x 10 x 2.5 mmpack of...

Price 11.70€
More
On sale upon request

Reference: 111/30

Slot head set

Review(s): 0

The kit contains: Ord.No. 11/51      PH0, PH1 Ord.No. 11/52      SW 2,5 / 4,0 Ord.No. 111/31    SW 2,0 / 3,5 Ord.No. 111/32    PH000, PH00 Ord.No. 111/33    PZ0, PZ1

Price 65.70€
More
On sale upon request

Reference: 55/8

12 x 28 x 8 mm

Review(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 12 x 28 x 8 mmpack of...

Price 14.80€
More
On sale upon request

Reference: 94/3

Thrust bearing 4 x 10 x 3 mm

Review(s): 0

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 4 x 10 x 3...

Price 11.70€
More
On sale upon request

Reference: 116/98

Manifold 34 mm

Review(s): 0

The various exhaust manifolds differ in shape and in the size of the flange, to match different engines' exhaust stubs. The term "exhaust hole spacing" refers to the holes on either side of the exhaust port, measured between hole centres.Please check before you order that you have selected the correct manifold to match your model and engine. Measure again...

Price 114.50€
More
On sale upon request

Reference: 84

3 x 10 x 4 mm

Review(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 3 x 10 x 4 mmpack of...

Price 11.70€
More
On sale upon request

Reference: 72/31

Swivel bearing 8 x 16 x 8 mm

Review(s): 0

A swivel bearing is fitted with a ball which is capable of rotation in all directions; this application is used in the swashplate. The dimensions of a swivel bearing mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Swivel bearing 8 x 16 x 8 mmpack of 1

Price 23.80€
More
On sale upon request

Reference: 11/67

Crankshaft nut socket spanner 14 mm

Review(s): 0

If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 14 mm, for O.S. 4-stroke

Price 23.90€
More
On sale upon request