Marcas

Ninguna marca

Referencia: 060

Bulon 3.5 mm - M 2.0 x 5.0

Reseña(s): 0

Estos pernos de punta esférica ofrecen una conexión óptima entre un brazo de salida de servo GRP y la varilla de empuje a la mecánica. Debajo del brazo de salida, bloquea el perno de bola con una tuerca hexagonal M 2. Para brazos de salida de aluminio, utiliza pernos de punta esférica. 060/7 y fluido de bloqueo de hilo.

Precio 13,80 €
Más
En venta bajo pedido
Los productos más vendidos

Sistema de transmision de cola completo

17/10
Valoración 
cola de acero inoxidable de 8 mm de diametrosyste
73,00 €
Impuestos incluidos En venta bajo pedido
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción
cola de acero inoxidable de 8 mm de diametrosyste
Detalles del producto
17/10
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Sistema de transmision de cola completo

Sistema de transmision de cola completo

cola de acero inoxidable de 8 mm de diametrosyste
Escriba su propia reseña
16 altri prodotti della stessa categoria:

Riferimento: 800/9

PTFE bush guide for 0.8 mm tailboom

Recensioni: 0

PTFE guides in the tail boom provide the necessary "lubrication" for the drive shaft, which eliminates the need to oil the system separately.PTFE guide for 0.8 mm tail boomPack of 3 

Prezzo 17,20 €
Più
In vendita su richiesta

Riferimento: 17/7

Articulated centre support

Recensioni: 0

The use of an articulated centre support in helicopters with extreme high mounted tail booms (e.g. Hughes 500) helps to balance up to 30 mm vertical off-set between mechanics and tail rotor. The centre support is double ballraced and pre-assembled.

Prezzo 67,70 €
Più
In vendita su richiesta

Riferimento: 17/16

Stainless steel tube 6.0 x 0.3 x 950 mm

Recensioni: 0

Advanced pilots appreciate the more precise control response of a rigid tail rotor drive system, as provided by a stainless steel drive shaft. Stainless steel tube 6.0 x 0.3 x 950 mm

Prezzo 30,00 €
Più
In vendita su richiesta

Riferimento: 17/13

Articulated joint tail drive system

Recensioni: 0

On a model helicopter like the Hughes 500 e.g. the tail boom is extremely high connected. Therefore an articulated centre support is applied in addition to the articulated tail drive system. The centre support is double ballraced and pre-assembled.Articulated joint tail drive systemwith articulated centre support

Prezzo 138,60 €
Più
In vendita su richiesta

Riferimento: 17

Tail rotor shaft 2 mm

Recensioni: 0

The 2 mm steel tail rotor shaft has proved its worth for several decades, especially in beginners' models.Drive shaft, steel, 2.0 x 980 mm

Prezzo 5,60 €
Più
In vendita su richiesta

Riferimento: 17/20

Stainless steel tail drive system

Recensioni: 0

This version of the ballraced tail rotor drive system is designed for installation in full-fuselage models. Power is transmitted by a 6 mm stainless steel drive shaft with a length of 980 mm.This length ensures that the system can be used in virtually all our larger fuselages, provided that the main and tail rotors are fitted with the articulated...

Prezzo 93,80 €
Più
In vendita su richiesta

Riferimento: 17/14

Stainless steel tail drive system for 20 mm

Recensioni: 0

Of course the explanation of Ord.No. 17/10 concerning a 2 mm steel drive wire in acrobatics applies not only for fuselages, it is similar for training helicopters.When you convert a trainer you use the existing tail boom. Main gearbox and tail gearbox have to be provided with a claw connector 49/12 each.Models over a certain age should be checked whether...

Prezzo 88,90 €
Più
In vendita su richiesta