Marcas

Ninguna marca

Proveedores
Los productos más vendidos

Cizallas para paneles de acristalamiento

11/26
Valoración 

Estas potentes y afiladas cizallas simplifican la tarea de cortar los componentes de la carrocería moldeados al vacío. Los paneles de acristalamiento, los tanques de combustible falsos, etc. se cortan fácilmente a lo largo de las líneas moldeadas con estas tijeras especiales.
Sugerimos no cortar nada hasta que esté satisfecho con las dimensiones exactas. Esto se debe a que las piezas de PRFV (fuselajes, etc.) se fabrican a mano y pueden producirse pequeñas diferencias en el proceso de fabricación.
Los mangos cómodos y las cuchillas cortas facilitan el corte de líneas curvas.

28,10 €
Impuestos incluidos En venta bajo pedido
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción

Estas potentes y afiladas cizallas simplifican la tarea de cortar los componentes de la carrocería moldeados al vacío. Los paneles de acristalamiento, los tanques de combustible falsos, etc. se cortan fácilmente a lo largo de las líneas moldeadas con estas tijeras especiales.
Sugerimos no cortar nada hasta que esté satisfecho con las dimensiones exactas. Esto se debe a que las piezas de PRFV (fuselajes, etc.) se fabrican a mano y pueden producirse pequeñas diferencias en el proceso de fabricación.
Los mangos cómodos y las cuchillas cortas facilitan el corte de líneas curvas.

Detalles del producto
11/26
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Cizallas para paneles de acristalamiento

Cizallas para paneles de acristalamiento

Estas potentes y afiladas cizallas simplifican la tarea de cortar los componentes de la carrocería moldeados al vacío. Los paneles de acristalamiento, los tanques de combustible falsos, etc. se cortan fácilmente a lo largo de las líneas moldeadas con estas tijeras especiales.
Sugerimos no cortar nada hasta que esté satisfecho con las dimensiones exactas. Esto se debe a que las piezas de PRFV (fuselajes, etc.) se fabrican a mano y pueden producirse pequeñas diferencias en el proceso de fabricación.
Los mangos cómodos y las cuchillas cortas facilitan el corte de líneas curvas.

Escriba su propia reseña
16 autres produits dans la même catégorie :

Référence: 64/2

Flywheel puller

Commentaire(s): 0

If the flywheel of the clutch is sitting to tight on the tapper of the collet you can use this flywheel puller.For this purpose you remove the nut from the crankshaft, then put the puller on the crankshaft, and turn both socket-head cap screws equally approx. 5 mm into the thread of the flywheel; the flywheel loosens now.The length of the socket-head cap...

Prix 11,20 €
Détails
En vente sur demande

Référence: 11/60

Tubing cutter, up to 15 mm Ø

Commentaire(s): 0

The tubing cutter can handle aluminium, stainless steel and brass tubing up to 15 mm diameter. It can also be used to form a slight internal burr on tubing. For example if you use a tail rotor pushrod running in a PTFE sleeve in aluminium tubing, you can cut the aluminium to length at both ends with the tubing cutter, and the PTFE sleeve will not slip out.

Prix 33,30 €
Détails
En vente sur demande

Référence: 70/22

Die M 3.0 HSS

Commentaire(s): 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prix 37,80 €
Détails
En vente sur demande

Référence: 11/86

Pushrod measuring holder

Commentaire(s): 0

Model helicopter building instructions always state pushrod length as measured from ball centre to ball centre.Determining this dimension using conventional measuring tools is not really much more accurate than estimating the length.Pushrod measuring holderpack of 2holders fit any standard calipers

Prix 14,80 €
Détails
En vente sur demande

Référence: 11/260

Glazing panel shears straight

Commentaire(s): 0

These powerful, sharp shears simplify the task of cutting out vacuum-moulded bodywork components. Glazing panels, dummy fuel tanks etc. are easily cut out along the moulded-in lines using these special shears. We suggest not to cut out anything until you satisfy yourself with the exact dimensions. This is because GRP parts (fuselages etc.) are hand made...

Prix 32,30 €
Détails
En vente sur demande

Référence: 70/21

Die M 2.0 HSS

Commentaire(s): 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prix 54,60 €
Détails
En vente sur demande

Référence: 11/28

Glasspaper file, flat

Commentaire(s): 0

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Prix 14,80 €
Détails
En vente sur demande

Référence: 70/20

Die M 2.5 HSS

Commentaire(s): 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prix 46,10 €
Détails
En vente sur demande

Référence: 21/11

Tool case

Commentaire(s): 0

Tool case, complete empty, alone, including foam to cutsize approx. 275 x 230 x 83 mm

Prix 19,10 €
Détails
En vente sur demande

Référence: 90/10

File set with handle, six-part

Commentaire(s): 0

This special file set is particularly useful when you are cutting small openings, as they can be used to work on the tiniest of radii and straight edges. The rotary-action handle makes quick work of swapping individual tools. The collet can also be used to grip drills and taps of 2 to 5 mm ∅.

Prix 17,00 €
Détails
En vente sur demande

Référence: 9/5

Protective goggles

Commentaire(s): 0

When handling tools it is in your own interests to read and observe the safety information and constantly to be aware of the possible hazards, before you have a really close encounter with a workpiece which, for whatever reason, flies off. Wear these protective goggles when grinding, turning and machining, and also when you are cutting off steel rod....

Prix 14,80 €
Détails
En vente sur demande

Síganos en Facebook