Arandela portapalas

Reference: 76/18

Blade holder twin blade bolt

Component part for a multi-blade rotor head for 10 mm or 12 mm Ø main shaft.

Reference: 78/41

Mixer lever cranked

Mixer lever, content of the package 1 piece.Additionial accessories for the use of mixer levers are either two flanged ballraces or two flanged bushes from Delrin as a low cost alternative. The screwing on the blade holder arm complies with the kind of hole, i.e. it depends on the through hole or on the blind hole. Please note for choosing the screws:...

Reference: 702/76

GRP blade holder, 22 mm blade throat

This blade holder was specially developed for the large Bell 47 G III with a rotor diameter of 2.36 m. It has a 22 mm blade throat and a 6 mm Ø bore for the retaining screw, i.e. the matching blade holder screws and self-locking nuts are M6 in size.

Reference: 87/21

Washer for actuator arm 2.5 x 9 mm

Washer for actuator arm Content of the package: 2 pieces

Reference: 71/4

Pitch mixer centre piece 10 mm

Pitch mixer centre piece, aluminium, 10 mm ∅

Reference: 832/72

Aluminium centre piece, 12 mm

Aluminium centre piece for rotor head 722/72.

Reference: 74/20

O-ring 3 x 11 mm, for CSS rotor head

O-ring 3 x 11 mm for CSS rotor head Content of the package: 2 pieces Tip: O-rings always slide with a drop of silicone oil onto the shaft.

Reference: 74/7

Rotor head dampers for 2 blade FBL systems

Flybarless electronics have now become common. Where they are being used harder damping is required.For these cases Vario is now offering a harder damping of the blade shaft provided by a pretension absorbing element in the centre block.For the adjustment, the outer O-ring position can be selected between "hard" and "soft" flight characteristics.Important...

Reference: 78/40

Mixer lever set

Mixer levers are an essential part of every flybar-controlled rotor head. From the swashplate a pushrod runs to the ballraced mixer arm which is screwed to the blade holder arm. The mixer levers transmit the control movement to the flybar via the double ball-link.Additionial accessories for the use of mixer levers are either two flanged ballraces or two...

Reference: 74/4

O-ring 2 x 4 mm soft

O-ring 2 x 4 mm soft Content of the package: 8 pieces Tip: O-rings always slide with a drop of silicone oil onto the shaft.

Reference: 72/45

Aluminium centre piece, 12 mm

Aluminium centre piece for 12 mm Ø main shaft

Reference: 80/10

Control bridge with metal balls

The control bridge actuates the flybar. The servos pass the control commands to the swashplate. The collective pitch compensator connected to the swashplate transfers the movement to the control bridge via the angled pushrods. The flybar accepts the control commands and passes them on to the blade holders and the rotor disc.Control bridge, GRP, for 4 mm ∅...

Reference: 72/1

CFRP rotor brake

When you have landed and stopped the engine, the rotor head continues spinning for quite some time until it stops by itself. A rotor brake shortens the time you have to wait. Using light pressure with the flat of your hand on the domed face of the rotor brake you can stop the rotor in a few moments. Pease note: stay in safe distance away from the turning...

Reference: 117/3

Spacer washer 10 x 24.6 mm

Spacer washer for rotor headPack of 2

Reference: 1005/8

Kit de conversión varillaje directo para JetRanger XL eléctrico

Reference: 74/21

O-ring 3.5 x 12 mm hard

O-ring 3.5 x 12 mm hard Content of the package: 8 pieces Tip: O-rings always slide with a drop of silicone oil onto the shaft.