Marcas

Ninguna marca

Los productos más vendidos

Amortiguador interno

603/23
Valoración 
Amortiguador interno
14,80 €
En venta bajo pedido
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción
Amortiguador interno
Detalles del producto
603/23
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Amortiguador interno

Amortiguador interno

Amortiguador interno
Escriba su propia reseña
16 other products in the same category:

Reference: 33/27

Rotor blade tie-down large

Review(s): 0

The rotor blade harness ranks as an essential accessory for full-size helicopters. These items prevent the blades swinging or rocking, and thereby exerting pressure on the rotor shaft. If that were to be allowed, in-flight failures could be attributed to it.Rotor blades set in motion by rising winds could also be damaged by striking obstacles. The rotor...

Price 32.60€
More
On sale upon request

Reference: 33/25

Rotor blade support

Review(s): 0

Any easy solution to the transport problem: The cut-out of this rotor blade support accommodates to the different shapes of tail booms on fuselages.Rotor blade supportfor fuselages, 30 x 270 x 200 mm

Price 26.60€
More
On sale upon request

Reference: 18/10

PTFE tube for tail drive shaft

Review(s): 0

PTFE is used as a bearing for the 2 mm wire tail drive shaft (Ord.No. 17) or as a support guide for the 2 mm piano wire push rod (Ord.No. 21 and 800/12) Length: approx. 740 mm

Price 12.80€
More
On sale upon request

Reference: 10/75

Glue dispenser

Review(s): 0

When you insert cartridges Ord.No. 10/73 into the dispenser and press the components through the mixing nozzle the epoxy is ready for immediate use.

Price 49.80€
More
On sale upon request

Reference: 3944

Servo mount 120°

Review(s): 0

When using a 4-point-linkage, the linkages from the servos run in a straight line to the swashplate.A 3-point-linkage does not permit this, here the linkages run diagonally.The 120° servo mounting enables inclined installation of the servos, and the results are straight running linkages to the swashplate.All Sky Fox based mechanics as well as on the...

Price 16.90€
More
On sale upon request

Reference: 97/4

Servo linkage set

Review(s): 0

When you build your first model helicopter you will find all the linkage components required to connect the servos to the mechanics supplied with the RC set (German radio systems only). When you come to installing servos in other models you can use this servo linkage set which contains all the link balls, screws, nuts and screw-fitting pushrod...

Price 40.10€
More
On sale upon request

Reference: 791/28

Wing brace

Review(s): 0

The wing brace prevents the wings vibrating; it can be installed in the Cobra, depending on model version.

Price 54.60€
More
On sale upon request

Reference: 3935/4

Servo extension lead 700 mm

Review(s): 0

When extending servo cables take into account that cable lengths over 500 mm requires a suppressor (Ord.No. 1040) to avoid interference.

Price 9.70€
More
On sale upon request

Reference: 8/3

Tail rotor flange

Review(s): 0

The GRP tail rotor flange is used in full-fuselage helicopters such as the Jet Ranger, Bell 222 etc. to attach the tail rotor to the tail boom. The flange is supplied oversized, so that it can be fitted in all fuselages. Simply trim it to match the inside shape of the tail end of the fuselage, then glue it in place using Poxan-622 or UHU-Plus, and fitted...

Price 9.70€
More
On sale upon request