Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Aste 3,0 x 75 mm Anteprima

Riferimento: 70/76

Aste 3,0 x 75 mm

Recensioni: 0

Ready-made pushrod, threaded M 3. Content of the package: 1 piece

Prezzo 6,30 €
Più
In vendita su richiesta
Tutte le migliori vendite

Screw fitting pushrod connector

97/9
Valutazione 



Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.

Caution during installation: the barrel of the connector must be free to rotate on the servo output arm or crank. Either use a 2 mm self-locking nut, or apply a little thread-lock fluid when fitting the M 2 hexagon nut. Be sparing with the fluid! Tighten the M 3 x 4 socket-head cap screw well to hold the pushrod securely. Do not use thread-lock fluid.

Screw fitting pushrod connector, with screw and nut, linkages of 1.5 - 2.0 mm

6,30 €
Tasse incluse
Quantità
In vendita su richiesta

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descrizione



Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.

Caution during installation: the barrel of the connector must be free to rotate on the servo output arm or crank. Either use a 2 mm self-locking nut, or apply a little thread-lock fluid when fitting the M 2 hexagon nut. Be sparing with the fluid! Tighten the M 3 x 4 socket-head cap screw well to hold the pushrod securely. Do not use thread-lock fluid.

Screw fitting pushrod connector, with screw and nut, linkages of 1.5 - 2.0 mm

Dettagli del prodotto
97/9
Recensioni

Ancora nessuna recensione da parte degli utenti.

Scrivi la tua recensione

Screw fitting pushrod connector

Screw fitting pushrod connector



Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.

Caution during installation: the barrel of the connector must be free to rotate on the servo output arm or crank. Either use a 2 mm self-locking nut, or apply a little thread-lock fluid when fitting the M 2 hexagon nut. Be sparing with the fluid! Tighten the M 3 x 4 socket-head cap screw well to hold the pushrod securely. Do not use thread-lock fluid.

Screw fitting pushrod connector, with screw and nut, linkages of 1.5 - 2.0 mm

Scrivi la tua recensione
16 altri prodotti della stessa categoria:
Servo extension lead 700 mm Anteprima

Riferimento: 3935/4

Servo extension lead 700 mm

Recensioni: 0

When extending servo cables take into account that cable lengths over 500 mm requires a suppressor (Ord.No. 1040) to avoid interference.

Prezzo 9,70 €
Più
In vendita su richiesta
Servo mount 120° Anteprima

Riferimento: 3944

Servo mount 120°

Recensioni: 0

When using a 4-point-linkage, the linkages from the servos run in a straight line to the swashplate.A 3-point-linkage does not permit this, here the linkages run diagonally.The 120° servo mounting enables inclined installation of the servos, and the results are straight running linkages to the swashplate.All Sky Fox based mechanics as well as on the...

Prezzo 19,40 €
Più
In vendita su richiesta
Protezione capottina per Lama Anteprima

Riferimento: 330/10

Protezione capottina per Lama

Recensioni: 0

This protective sheath provides effective protection to the cabin of your valuable helicopter, and helps to avoid unsightly scratches. It is simply pulled over the cabin and closed with a hook -and-loop fastener.Cabin sheath for Lamamatching the cabins of the models 3300 and 3400

Prezzo 62,80 €
Più
In vendita su richiesta
Rotor blade tie-down Anteprima

Riferimento: 33/28

Rotor blade tie-down

Recensioni: 0

Rotor blade tie-downs are an essential feature of full-size helicopter life. The tie-down protects the blades from swinging, rocking and stretching, and thereby prevents excessive pressure on the rotor shaft. If these measures were not taken the result could easily be in-flight mechanical failure; rotor blades spinning as the wind rises could strike...

Prezzo 30,60 €
Più
In vendita su richiesta
Servo numbers Anteprima

Riferimento: 3948

Servo numbers

Recensioni: 0

Cable spaghetti? We all know the problem of allocating the servo leads to the receiver outputs. Here's the answer: number them like the pro's do! Simply put the receiver channel number on each lead; they can be removed just as easily. The pack contains three sets of 10, numbered from 0-9, in different colours.Servo numbers, pack of 30

Prezzo 11,20 €
Più
In vendita su richiesta
Quick-release servo mount Anteprima

Riferimento: 3947

Quick-release servo mount

Recensioni: 0

During construction we often need that "third hand", and there are times when it would be really useful to be able to see assemblies from front and rear at the same time.Servo installation is fast and reliable using the quick-release servo mount.The mounting plates are simply positioned either in front of the servo or behind it - whichever is more...

Prezzo 9,80 €
Più
In vendita su richiesta

Seguici su Facebook

Facebook