Marcas

Ninguna marca

Referencia: 060

Bulon 3.5 mm - M 2.0 x 5.0

Reseña(s): 0

Estos pernos de punta esférica ofrecen una conexión óptima entre un brazo de salida de servo GRP y la varilla de empuje a la mecánica. Debajo del brazo de salida, bloquea el perno de bola con una tuerca hexagonal M 2. Para brazos de salida de aluminio, utiliza pernos de punta esférica. 060/7 y fluido de bloqueo de hilo.

Precio 13,80 €
Más
En venta bajo pedido
Los productos más vendidos

Brida del rotor de cola

8/3
Valoración 
Cola plato de rotor
8,30 €
Impuestos incluidos En venta bajo pedido
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción
Cola plato de rotor
Detalles del producto
8/3
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Brida del rotor de cola

Brida del rotor de cola

Cola plato de rotor
Escriba su propia reseña
16 altri prodotti della stessa categoria:

Riferimento: 3944

Servo mount 120°

Recensioni: 0

When using a 4-point-linkage, the linkages from the servos run in a straight line to the swashplate.A 3-point-linkage does not permit this, here the linkages run diagonally.The 120° servo mounting enables inclined installation of the servos, and the results are straight running linkages to the swashplate.All Sky Fox based mechanics as well as on the...

Prezzo 14,20 €
Più
In vendita su richiesta

Riferimento: 97/4

Servo linkage set

Recensioni: 0

When you build your first model helicopter you will find all the linkage components required to connect the servos to the mechanics supplied with the RC set (German radio systems only). When you come to installing servos in other models you can use this servo linkage set which contains all the link balls, screws, nuts and screw-fitting pushrod...

Prezzo 32,80 €
Più
In vendita su richiesta

Riferimento: 3935/4

Servo extension lead 700 mm

Recensioni: 0

When extending servo cables take into account that cable lengths over 500 mm requires a suppressor (Ord.No. 1040) to avoid interference.

Prezzo 8,90 €
Più
In vendita su richiesta

Riferimento: 330/10

Protezione capottina per Lama

Recensioni: 0

This protective sheath provides effective protection to the cabin of your valuable helicopter, and helps to avoid unsightly scratches. It is simply pulled over the cabin and closed with a hook -and-loop fastener.Cabin sheath for Lamamatching the cabins of the models 3300 and 3400

Prezzo 50,20 €
Più
In vendita su richiesta

Riferimento: 3941/90

Servo mounting set

Recensioni: 0

Rubber servo mounting grommets absorb vibration and also help to protect the servos.Servo mounting set, for 2 JR servos

Prezzo 11,70 €
Più
In vendita su richiesta

Riferimento: 33/27

Rotor blade tie-down large

Recensioni: 0

The rotor blade harness ranks as an essential accessory for full-size helicopters. These items prevent the blades swinging or rocking, and thereby exerting pressure on the rotor shaft. If that were to be allowed, in-flight failures could be attributed to it.Rotor blades set in motion by rising winds could also be damaged by striking obstacles. The rotor...

Prezzo 27,00 €
Più
In vendita su richiesta

Riferimento: 97/9

Screw fitting pushrod connector

Recensioni: 0

Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.Caution during installation: the barrel of the...

Prezzo 4,40 €
Più
In vendita su richiesta

Riferimento: 13/21

Magnets for speed regulator

Recensioni: 0

These magnets are suitable for use with all commercial speed regulators. For installation in the mechanics it is advisable the magnets be glued in a clamp ring Ord.No. 54/6, or as in the photo on the internal-tooth gear ring. Pack of 3

Prezzo 9,50 €
Più
In vendita su richiesta