Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Tutte le migliori vendite

Tail rotor flange

8/3
Valutazione 


The GRP tail rotor flange is used in full-fuselage helicopters such as the Jet Ranger, Bell 222 etc. to attach the tail rotor to the tail boom.
The flange is supplied oversized, so that it can be fitted in all fuselages. Simply trim it to match the inside shape of the tail end of the fuselage, then glue it in place using Poxan-622 or UHU-Plus, and fitted with screws where necessary. Use an M 3 tap (Order No. 11/78) to cut a thread in the flange to take the tail rotor retaining screws.

  • Tail rotor flange
  • GRP, 2-part
9,70 €
Tasse incluse
Quantità
In vendita su richiesta

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descrizione


The GRP tail rotor flange is used in full-fuselage helicopters such as the Jet Ranger, Bell 222 etc. to attach the tail rotor to the tail boom.
The flange is supplied oversized, so that it can be fitted in all fuselages. Simply trim it to match the inside shape of the tail end of the fuselage, then glue it in place using Poxan-622 or UHU-Plus, and fitted with screws where necessary. Use an M 3 tap (Order No. 11/78) to cut a thread in the flange to take the tail rotor retaining screws.

  • Tail rotor flange
  • GRP, 2-part
Dettagli del prodotto
8/3
Recensioni

Ancora nessuna recensione da parte degli utenti.

Scrivi la tua recensione

Tail rotor flange

Tail rotor flange


The GRP tail rotor flange is used in full-fuselage helicopters such as the Jet Ranger, Bell 222 etc. to attach the tail rotor to the tail boom.
The flange is supplied oversized, so that it can be fitted in all fuselages. Simply trim it to match the inside shape of the tail end of the fuselage, then glue it in place using Poxan-622 or UHU-Plus, and fitted with screws where necessary. Use an M 3 tap (Order No. 11/78) to cut a thread in the flange to take the tail rotor retaining screws.

  • Tail rotor flange
  • GRP, 2-part
Scrivi la tua recensione
16 autres produits dans la même catégorie :
Magnets for speed regulator Aperçu rapide

Référence: 13/21

Magnets for speed regulator

Commentaire(s): 0

These magnets are suitable for use with all commercial speed regulators. For installation in the mechanics it is advisable the magnets be glued in a clamp ring Ord.No. 54/6, or as in the photo on the internal-tooth gear ring. Pack of 3

Prix 11,70 €
Détails
En vente sur demande
Rotor blade tie-down large Aperçu rapide

Référence: 33/27

Rotor blade tie-down large

Commentaire(s): 0

The rotor blade harness ranks as an essential accessory for full-size helicopters. These items prevent the blades swinging or rocking, and thereby exerting pressure on the rotor shaft. If that were to be allowed, in-flight failures could be attributed to it.Rotor blades set in motion by rising winds could also be damaged by striking obstacles. The rotor...

Prix 37,50 €
Détails
En vente sur demande
PTFE tube for tail drive shaft Aperçu rapide

Référence: 18/10

PTFE tube for tail drive shaft

Commentaire(s): 0

PTFE is used as a bearing for the 2 mm wire tail drive shaft (Ord.No. 17) or as a support guide for the 2 mm piano wire push rod (Ord.No. 21 and 800/12) Length: approx. 740 mm

Prix 12,80 €
Détails
En vente sur demande
Screw fitting pushrod... Aperçu rapide

Référence: 97/9

Screw fitting pushrod connector

Commentaire(s): 0

Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.Caution during installation: the barrel of the...

Prix 6,30 €
Détails
En vente sur demande
Servo linkage set Aperçu rapide

Référence: 97/4

Servo linkage set

Commentaire(s): 0

When you build your first model helicopter you will find all the linkage components required to connect the servos to the mechanics supplied with the RC set (German radio systems only). When you come to installing servos in other models you can use this servo linkage set which contains all the link balls, screws, nuts and screw-fitting pushrod...

Prix 46,10 €
Détails
En vente sur demande
Servo extension lead 700 mm Aperçu rapide

Référence: 3935/4

Servo extension lead 700 mm

Commentaire(s): 0

When extending servo cables take into account that cable lengths over 500 mm requires a suppressor (Ord.No. 1040) to avoid interference.

Prix 9,70 €
Détails
En vente sur demande

Seguici su Facebook

Facebook