Funda de transporte para 2x3-palas o 2500 mm

Référence: 10/75

Glue dispenser

When you insert cartridges Ord.No. 10/73 into the dispenser and press the components through the mixing nozzle the epoxy is ready for immediate use.

Référence: 3941/90

Servo mounting set

Rubber servo mounting grommets absorb vibration and also help to protect the servos.Servo mounting set, for 2 JR servos

Référence: 18/12

Aluminium tube 4.0 x 3.0 x 1000 mm

Aluminium tube 4.0 x 3.0 x 1000 mm

Référence: 18/9

PVC tube 4.5 x 3.3 x 380 mm, white

PVC tube 4.5 x 3.3 x 380 mm, white

Référence: 97/4

Servo linkage set

When you build your first model helicopter you will find all the linkage components required to connect the servos to the mechanics supplied with the RC set (German radio systems only). When you come to installing servos in other models you can use this servo linkage set which contains all the link balls, screws, nuts and screw-fitting pushrod...

Référence: 21

Pushrod 1.5 x 1000 mm, steel

Pushrod 1.5 x 1000 mm, steel

Référence: 33/3

Rotor blade pouch 3-blade Ø 2500 mm

Référence: 97/9

Screw fitting pushrod connector

Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.Caution during installation: the barrel of the...

Référence: 13/21

Magnets for speed regulator

These magnets are suitable for use with all commercial speed regulators. For installation in the mechanics it is advisable the magnets be glued in a clamp ring Ord.No. 54/6, or as in the photo on the internal-tooth gear ring. Pack of 3

Référence: 10/1

Dispenser for UHU plus endfest 300

Using the dispenser allows UHU plus endfest 300 to be allotted exactly, evenly and economically. The special feature of this dispenser is the enclosed mixing nozzle, which mixes the adhesive ready for use.

Référence: 603/16

Tail boom set, Schweizer 300 C

Component part for fuselages, Ord.No. 6030 or 6031.

Référence: 305/18

Halter Kugellager

Référence: 3936/1

Y-lead

If you want to operate two servos in parallel from one receiver channel you requires a Y-lead.

Référence: 890/25

Cooling fan support for Schweizer 300 C

Component part for fuselage, Ord.No. 6030 or 6031.

Référence: 3944

Servo mount 120°

When using a 4-point-linkage, the linkages from the servos run in a straight line to the swashplate.A 3-point-linkage does not permit this, here the linkages run diagonally.The 120° servo mounting enables inclined installation of the servos, and the results are straight running linkages to the swashplate.All Sky Fox based mechanics as well as on the...

Référence: 8/3

Tail rotor flange

The GRP tail rotor flange is used in full-fuselage helicopters such as the Jet Ranger, Bell 222 etc. to attach the tail rotor to the tail boom. The flange is supplied oversized, so that it can be fitted in all fuselages. Simply trim it to match the inside shape of the tail end of the fuselage, then glue it in place using Poxan-622 or UHU-Plus, and fitted...