Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Aste 3,0 x 75 mm Anteprima

Riferimento: 70/76

Aste 3,0 x 75 mm

Recensioni: 0

Ready-made pushrod, threaded M 3. Content of the package: 1 piece

Prezzo 6,30 €
Più
In vendita su richiesta
Tutte le migliori vendite

Ci sono 420 prodotti.

Ordina per:
Rilevanza Nome, da A a Z Nome, da Z ad A Prezzo, da meno caro a più caro Prezzo, da più caro a meno caro
Visualizzati 169-180 su 420 articoli

Filtri attivi

Swashplate driver for rotor... Anteprima

Riferimento: 68/20-5

Swashplate driver for rotor head 705/30

Recensioni: 0

Where a pitch compensator sits and two pushrods connect to the flybar, this is now a swashplate driver in its place.This is necessary to drive the inner ring of the swashplate in order to always control the blade angle in the same position.Aluminium swashplate driver with 4 ballraces.

Prezzo 87,20 €
Più
In vendita su richiesta
Albero del rotore 10 x 286 mm Anteprima

Riferimento: 35/41

Albero del rotore 10 x 286 mm

Recensioni: 0

 Rotor shaftfor multi-blade headhole spacing 35 mmuse with a Schweizer 300 C with multi-blade head only!

Prezzo 86,90 €
Più
In vendita su richiesta
Rete a benzina fine e... Anteprima

Riferimento: 830/68

Rete a benzina fine e filtro a cherosene

Recensioni: 0

Chemical analysis used in Formel 1 is able to determine 1 g of impurity within 1 ton of oil. To fulfill your demand on the cleanness of the fuel for your model helicopter you use the fine-mesh petrol filter inside the fuel tubing between the tank and the carburettor. Also suitable for kerosine turbine fuel.

Prezzo 25,10 €
Più
In vendita su richiesta
Fieltro clunk pick-up Anteprima

Riferimento: 26/30

Fieltro clunk pick-up

Recensioni: 0

Felt clunk pick-up 16 Ø x 26 mmfor bubbles-free suck up and constant flow ofpetrol and kerosene

Prezzo 16,90 €
Più
In vendita su richiesta
Tuned pipe silencer Anteprima

Riferimento: 116/76

Tuned pipe silencer

Recensioni: 0

 Tuned pipe silenceroverall length 350 mmconnection-Ø 20 mmoverall Ø 40 mmsilencer chamber 240 mmweight approx. 190 gtail pipe length 45 mm

Prezzo 176,40 €
Più
In vendita su richiesta
Tuned pipe holder for... Anteprima

Riferimento: 310/3

Tuned pipe holder for fuselages

Recensioni: 0

The shape of a fuselage is not always correct to support the tuned pipe at the exit (e.g. model Tiger).Tuned pipe holder for fuselagesset suitable for tuned pipe 116/33

Prezzo 34,30 €
Più
In vendita su richiesta
Ball connector Anteprima

Riferimento: 68/21

Ball connector

Recensioni: 0

GRPfor swashplate drivers Ord.No. 68/20 and 68/50

Prezzo 11,20 €
Più
In vendita su richiesta
Flywheel puller Anteprima

Riferimento: 64/2

Flywheel puller

Recensioni: 0

If the flywheel of the clutch is sitting to tight on the tapper of the collet you can use this flywheel puller.For this purpose you remove the nut from the crankshaft, then put the puller on the crankshaft, and turn both socket-head cap screws equally approx. 5 mm into the thread of the flywheel; the flywheel loosens now.The length of the socket-head cap...

Prezzo 11,20 €
Più
In vendita su richiesta
Torna all'inizio

Seguici su Facebook

Facebook