Rotor Principal de 5 palas, 10 mm

Reference: 703/34

3 blade rotor head, 12 mm

Not available

Reference: 1005/52

Rotor head up to 2500 mmOrd.No. 1005/52

Ord.No. 1005/52 is for a Ø 15 mm rotor shaft and Ord.No. 1005/49 for Ø 12 mm rotor shaft

Reference: 702/75

Semi scale rotor head

With the SKS semi-scale rotor head you will take the advantage of a mechanical gyro system with a delay in control commands caused by the flybar level.This system suits the scale looks of a UH-1D....

Reference: 702/60

CSS 2-blade-rotor head 10 mm / ø5 mm

CSS stands for Cyclic Speed System at this rotor head because the cyclic control occurs more spontaneous.As, for example, a Jet Ranger or an AIRWOLF requires a true-scale look in the air, a rotor head without a flybar is part of the scale detail for these helicopters. Because of its exact reactions in flight we recommend this CSS rotor head.Only the...

Reference: 702/62

Rigid 2 blade rotor head 12 mm

Not available

Reference: 702/59

2-Blade-Rigid-Rotor head for 10 mm / ø4 mm

Not available

Reference: 704/38

4-blade rotor head 12 mm

4-blade rotor head 12 mm for 18 mm

Reference: 1005/47

Bell 47 G rotor head

This rotor head was modelled as closely as possible on the original version installed on the Bell 47 G full-size helicopter. It is an excellent choice for use on the Bell 47 G III model, Ord. No. 4700.The centrifugal weights and springs are dummies, and do not work. The rotor blade swivel limits are also imitations, and have no function.The blade grips...

Reference: 704/36

4-blade rotor head 12 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 703/40

3-blade rotor head for 12 mm, for Lama

Large models require strong, rigid rotor heads which are designed to cope with the demands of a rotor disc of commensurate size, and are built for mounting on a 12 mm Ø rotor shaft. The only...

Reference: 702/70

Semi scale rotor head

This semi-scale rotor head includes additional mixing of the blade holder actuator linkage at a ratio of 2 : 1. This results in well-balanced flying characteristics, and the model has a damped rather than direct response to your control inputs (resembling a 2-blade head with flybar).Use only the suggested rotor blades for flybar-less rotor heads,...

Reference: 1005/50

Sky Fox rotor head

The Sky Fox rotor head in its original form is robust and very sturdy, so it can achieve good results in all flight positions.The rotor head is supplied with a ball raced pitch compensator and two main shaft collars, their use depends on the length of the rotor shaft.CautionIt is not permissible to use this rotor head on a mechanical system powered by a...

Reference: 704/34

4-blade rotor head 12 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 706/20

6-Blatt Rotorkopf für Ø 12 mm Welle

Reference: 705/32

5-blade rotor head 12 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 705/34

5-blade rotor head 12 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...