Stainless steel clamp, 50 mm

Riferimento: 330/18

Gear support for tail drive

Component part for fuselages like Air-Crane, Bell 47 or Lama.Pack of 3

Riferimento: 75

8 x 16 x 4 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 8 x 16 x 4 mmpack of...

Riferimento: 117/2

Thrust bearing 10 x 24 x 9 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 10 x 24 x 9...

Riferimento: 10/73

Five minute epoxy, 50 ml

The more you build, the more frequently you use epoxies, whose components must be proportionately mixed. When you insert cartridges into the dispenser and press the components through the mixing nozzle the epoxy is ready for immediate use. Pack of 50 ml, pot life approx. 5 minutes

Riferimento: 11/67

Crankshaft nut socket spanner 14 mm

If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 14 mm, for O.S. 4-stroke

Riferimento: 715/80

Steel manifold for Mizar

 Steel manifold for Mizar with petrol engine34 mm hole spacinge.g. for ZG22 or G230

Riferimento: 64/33

bell pinion gear 23-tooth

Clutch bell pinion gear23-toothmodule 1material: aluminiumtwin ballracedincl. clutch liningfits the glow plug motor clutch

Riferimento: 99 A

6 x 10 x 2.5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 6 x 10 x 2.5 mmpack of...

Riferimento: 117/8

Thrust bearing 8 x 15 x 5 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 8 x 15 x 5...

Riferimento: 116/94

Silencer for 116/95

Silencer, aloneIntake pipe 170 mmSilencer chamber 195 mmOverall Ø 50 mm

Riferimento: 55/9

ball bearing 12 x 28 x 7 mm

Not available

Riferimento: 870/49

Servo frame CFK

Riferimento: 870/53

Bearing plate, GFK

Not available

Riferimento: 55/3

Thrust bearing 10 x 25 x 6 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence.The dimensions of a ballrace mean:inside diameter (I.D.) x outside diameter (O.D.) x thickness.Thrust bearing 10 x 25 x 6...

Riferimento: 55/2

Bearing 8 x 19 x 6 mm

Not available

Riferimento: 71/7

Bearing 2 x 6 x 2,5 mm

Not available