Marcas

Ninguna marca

Proveedores
Los productos más vendidos

Soporte del tubo de cola

260/7
Valoración 
Titular de la pluma de cola
99,90 €
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción
Titular de la pluma de cola
Detalles del producto
260/7
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Soporte del tubo de cola

Soporte del tubo de cola

Titular de la pluma de cola
Escriba su propia reseña
16 autres produits dans la même catégorie :

Référence: 800/24

Kit empennage, grand

Commentaire(s): 0

If you fit a large stabiliser to your trainer there is no need for a tail skid. This stabiliser provides the tail rotor blades with enough ground clearance, and offers good flight stability at low airspeeds. There are two versions with different methods of attachment.height 275 mm118 g total weightwith clamp for 20 mm Ø tail booms

Prix 30,60 €
Détails
En vente sur demande

Référence: 800/50

Empennage 3-D en fibre de carbone

Commentaire(s): 0

When you are attempting high-speed flying in reverse and also certain pirouettes you may find that the helicopter's heading changes due to the influence of the solid vertical stabiliser. That is the basic reason for the development of this special 3-D tail.It is very strong, and its large size removes the need for a tail skid. The stabiliser is...

Prix 62,80 €
Détails
En vente sur demande

Référence: 800/37

Support de verrière 26 mm

Commentaire(s): 0

The required length of the canopy holder is determined by the kind of canopy and the location of its fitting points on the side frames.

Prix 11,20 €
Détails
En vente sur demande

Référence: 800/25

Kit empennage, grand

Commentaire(s): 0

If you fit a large stabiliser to your trainer there is no need for a tail skid. This stabiliser provides the tail rotor blades with enough ground clearance, and offers good flight stability at low airspeeds. There are two versions with different methods of attachment.275 mm high118 g total weightscrew fitting to tail rotor holder

Prix 30,60 €
Détails
En vente sur demande

Référence: 800/20

Béquille rouge

Commentaire(s): 0

Tail skids only. Create your own individual colour scheme: e.g. white stabiliser - red skid!

Prix 5,50 €
Détails
En vente sur demande

Référence: 310/8

Support de résonateur 70 mm

Commentaire(s): 0

GRP tuned pipe holders are used to secure the tuned pipe to the tail booms. They are easy to clamp in place. The tail pipe of the tuned pipe should be covered with silicone hose (Order No. 116/8), or with one of the tail pipes (Ord.No. 116/0 or 116/9), so that the heat of the pipe does not damage the holder.Tuned pipe holder, 2-partfor 20 mm ��tail boom

Prix 14,70 €
Détails
En vente sur demande

Référence: 118/62

Train d'atterrissage photo et vidéo

Commentaire(s): 0

Piloter un hélicoptère avec un train d'atterrissage pour photo et vidéo est un peu inhabituel, mais pas un problème en soi pour un pilote expérimenté. Ce train d'atterrissage peut être...

Prix 300,10 €
Détails
En vente sur demande

Référence: 800/5

Kit empennage rouge

Commentaire(s): 0

Instead of a horizontal fin (for mounting on the tail boom) the small inset horizontal panel replaces that. The inset fits on top of the stabiliser, outwards opposite of the tail rotor.220 mm high, excl. tail skid3-part, 45 g total weight

Prix 27,40 €
Détails
En vente sur demande

Síganos en Facebook