Pitot para Lama 1:4

Reference: 340/6

Entry step, for Lama

If you have a mind to continue adding detail fittings to your Lama, you are sure to appreciate this landing gear step which can be fitted to an existing model at any time. The step is made of stainless steel, and is supplied complete with clips, screw fittings and tread material. Entry step, for Lama, pack of 1

Reference: 134/444

Winch connections 1:4

dimensions:flat: 1.53 x 1.53 x 0.7 cmhigh: 1.29 x 1.29 x 1.14 cmPackage contains: 3x flat + 4x high

Reference: 30/50

Fire extinguisher approx. 70 mm long

Fire extinguishers in the cockpit are mandatory for any scale model helicopter, since the full-size machines are also required to carry them.Our fire extinguisher is available in two different sizes, and it can be mounted in the cockpit in a wide variety of positions.For models up to 2000 mm rotor diameter we recommend the smaller version; the bigger one...

Reference: 341/418

Reinforcements for skis Lama 1:4

Reference: 340/13

Dummy power unit

This dummy power unit can be installed on turbine powered helicopters to produce an even more realistic intersection between the turbine and the gearbox.When the imitation rotor brake of the dummy part is pushed over the turbine starter, the rubber connector is spring-loaded in front of the gearbox connection; retaining screws are not required.Dummy power...

Reference: 341/520

Battery housing /Lama

dimensions: 7.76 x 3.4 x 5.3 cm

Reference: 340/1

Wheel holder for Lama

The Lama is a large helicopter, and the supplementary wheels which can be attached to the landing gear make it much easier to move the machine into and out of the hangar. However, the wheels are removed prior to flying the model. These wheel holders for our model of the Lama are made of plastic and are simply glued to the 20 mm Ø skid tubes using UHU...

Reference: 330/2

Dummy turbine, GRP

The dummy turbine provides the ideal starting point if you wish to install additional scale fittings on your Lama.The dummy turbine is assembled from six separate GRP mouldings, and fits all models with VR-22 mechanics installed.In the turbine-powered version of the Lama the actual turbine is located in this position.GRP dummy turbineLength approx. 490 mm

Reference: 341/403

Front acces panel Lama 1:4

dimensions: 6 x 8.2 x 0.5 cm2-part

Reference: 341/36

Load basket

Load basket for Lamalength:410 mmwidth:100 mmheight70 mm

Reference: 341/421

Rueda de ventilador Lama 1: 4

Reference: 341/509

Lama BTP 1:5

dimensions: main part: 9.5 x 4.95 x 6.4 cm6-part

Reference: 350/17

Exhaust cover, Ø 90 mm

When the turbine of a full-size helicopter is not running, the engine is protected with an exhaust cover which prevents foreign objects finding their way inside the turbine. This exhaust cover for model turbines is suitable for the Lama, Alouette III and any other machine with a 90 mm Ø exhaust pipe. Caution: it is essential to allow the exhaust pipes to...

Reference: 341/402

Kerosene trap N1 1:4

dimensions: 4.3 x 2.5 cm, inner diameter: 1.43 cm

Reference: 10/96

Anti-collision light with red housing

Reference: 340/5

Snowboards for Lama

When full-size helicopters have to land in deep snow, the skids are fitted with "snowboards" to prevent them sinking in.On the model they look really good, and also help the pilot detect the model's orientation in the air.Make your model an eye-catcher and use some rivets for the decoration of the skies."Snowboards" for Lama, 1 pair