Tuned pipe silencer

Reference: 830/42

Exhaust mount 42 mm

  For silencer Ord.No. 116/96.Content of the package1 piece

Reference: 40/1

4 x 9 x 4 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 4 x 9 x 4 mmpack of...

Reference: 94/17

Thrust bearing 7 x 13 x 4.5 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 7 x 13 x 4.5...

Reference: 55/3

Thrust bearing 10 x 25 x 6 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence.The dimensions of a ballrace mean:inside diameter (I.D.) x outside diameter (O.D.) x thickness.Thrust bearing 10 x 25 x 6...

Reference: 64/33

bell pinion gear 23-tooth

Clutch bell pinion gear23-toothmodule 1material: aluminiumtwin ballracedincl. clutch liningfits the glow plug motor clutch

Reference: 11/67

Crankshaft nut socket spanner 14 mm

If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 14 mm, for O.S. 4-stroke

Reference: 64/0

9.5 x 22 x 5.5 imperial

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 9.5 x 22 x 5.5...

Reference: 4302

Glow plug Enya 6

Content of the package1 piecehot engine - cold plug (Summer) cold engine - hot plug (Winter)

Reference: 58/11

3 x 8 x 3 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 3 x 8 x 3 mmpack of...

Reference: 870/49

Servo frame CFK

Reference: 330/18

Gear support for tail drive

Component part for fuselages like Air-Crane, Bell 47 or Lama.Pack of 3

Reference: 715/80

Steel manifold for Mizar

 Steel manifold for Mizar with petrol engine34 mm hole spacinge.g. for ZG22 or G230

Reference: 39

8 x 22 x 7 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 8 x 22 x 7 mmpack of...

Reference: 11/66

Crankshaft nut socket spanner 10 mm

If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 10 mm, for O.S.

Reference: 55/6

12 x 21 x 5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 12 x 21 x 5 mmpack of...

Reference: 17/22

6 x 13 x 5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 6 x 13 x 5 mmpack of...