Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Aste 3,0 x 75 mm Anteprima

Riferimento: 70/76

Aste 3,0 x 75 mm

Recensioni: 0

Ready-made pushrod, threaded M 3. Content of the package: 1 piece

Prezzo 6,30 €
Più
In vendita su richiesta
Tutte le migliori vendite

Ci sono 99 prodotti.

Ordina per:
Rilevanza Nome, da A a Z Nome, da Z ad A Prezzo, da meno caro a più caro Prezzo, da più caro a meno caro
Visualizzati 1-12 su 99 articoli

Filtri attivi

  • Categorie: Alu-Tuning for 6 mm tail rotor
  • Categorie: Giunti
  • Categorie: Palini rotore di coda
  • Categorie: Ricambi e Accessori
Aluminium 2-bladed control... Anteprima

Riferimento: 101/60

Aluminium 2-bladed control bridge, hole Ø8, for shaft 6mm

Recensioni: 0

Aluminium 2-bladed control bridge, hole Ø8, for shaft 6mmThis control bridge can replace the plastic conrol bridge Ord.No. 101/6. As it is made from Aluminium, it is more rigid and more resistant to heat than the standard version.

Prezzo 44,30 €
Più
In vendita su richiesta
Aluminium 3-bladed control... Anteprima

Riferimento: 101/220

Aluminium 3-bladed control bridge, hole Ø8, for shaft 6mm

Recensioni: 0

Aluminium 3-bladed control bridge, hole Ø8, for shaft 6mmThis control bridge can replace the plastic control bridge Ord.No. 101/22. As it is made from aluminium, it is more rigid and resistant to heat than the standard version.

Prezzo 50,50 €
Più
In vendita su richiesta
Four-screw fixing, shaft 5 mm Anteprima

Riferimento: 49/9

Four-screw fixing, shaft 5 mm

Recensioni: 0

Contrary to common opinion steel wires should only be degreased before mounting, but not sanded. This would cause running out-of-centre. After the change steel drive wire you should not use the grubscrews anymore. The max. force originates each with starting (turning up the system), i.e. over a longer period the shaft leaves it's marks on the surfaces of...

Prezzo 27,40 €
Più
In vendita su richiesta
Aluminium 4-bladed control... Anteprima

Riferimento: 101/480

Aluminium 4-bladed control bridge, hole Ø8, for shaft 6mm

Recensioni: 0

 Aluminium 4-bladed control bridge, hole Ø8, for shaft 6mmThis control bridge can replace the plastic conrol bridge Ord.No.101/48. As it is made from Aluminium, it is more rigid and resistant to heat than the standard version. 

Prezzo 50,50 €
Più
In vendita su richiesta
Comando passo coda rinforzato Anteprima

Riferimento: 97/12

Comando passo coda rinforzato

Recensioni: 0

The forces generated by the tail rotor rise significantly with large, heavy model helicopters; larger tail rotor blades also have the same effect. This reinforced aluminium tail rotor bellcrank is the item of choice wherever high control power is required, as it prevents the lever twisting.Reinforced tail rotor bellcrank, complete with screw fixings

Prezzo 34,30 €
Più
In vendita su richiesta
Torna all'inizio

Seguici su Facebook

Facebook