Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Tutte le migliori vendite

Ci sono 72 prodotti.

Ordina per:
Rilevanza Nome, da A a Z Nome, da Z ad A Prezzo, da meno caro a più caro Prezzo, da più caro a meno caro
Visualizzati 61-72 su 72 articoli

Filtri attivi

  • Categorie: Piatto Oscillante i Accessori
  • Categorie: Ricambi e Accessori
Swashplate driver for rotor... Anteprima

Riferimento: 68/20-5

Swashplate driver for rotor head 705/30

Recensioni: 0

Where a pitch compensator sits and two pushrods connect to the flybar, this is now a swashplate driver in its place.This is necessary to drive the inner ring of the swashplate in order to always control the blade angle in the same position.Aluminium swashplate driver with 4 ballraces.

Prezzo 87,20 €
Più
In vendita su richiesta
Swashplate driver 10 mm Anteprima

Riferimento: 68/20

Swashplate driver 10 mm

Recensioni: 0

Where a pitch compensator sits and two pushrods connect to the flybar, this is now a swashplate driver in its place.This is necessary to drive the inner ring of the swashplate in order to always control the blade angle in the same position.Aluminium swashplate driver with 4 ballraces.

Prezzo 87,20 €
Più
In vendita su richiesta
Swashplate 5-blade Anteprima

Riferimento: 68/15

Swashplate 5-blade

Recensioni: 0

The swashplate disc can be controlled by 4 ball-end bolts at 90° or by 3 ball-end bolts at 120°, whether the linkage is direct to the servos or utilises bellcranks. As standard there are 4 linkage points.In both types the swashplate bolt assumes the additional function of one linkage point. For a 120° linkage the ball-end bolts have to be replaced with...

Prezzo 131,70 €
Più
In vendita su richiesta
Viti a brugola per... Anteprima

Riferimento: 054

Viti a brugola per fissaggio pale coda M3 x 20 G12

Recensioni: 0

Bolt using self-locking nuts don't need additional screw-retaining fluid. Of course this applies to the blade holder bolts on the main rotor head and on the tail rotor (as shown here). Blade holder bolts are counted among the special bolts with high tensile stength, where the shaft and thread length are matched to the application. Pack of 2 with...

Prezzo 4,70 €
Più
In vendita su richiesta
3-D swashplate 10 mm Anteprima

Riferimento: 68/14

3-D swashplate 10 mm

Recensioni: 0

This swashplate provides longer ball-end bolts on the inner ring for larger control travels, as required for 3-D flying.

Prezzo 108,30 €
Più
In vendita su richiesta
Swashplate guide Anteprima

Riferimento: 52/20

Swashplate guide

Recensioni: 0

The swashplate guide prevents the outer ring of the swashplate rotating; the swashplate pin runs in the slot in this guide. The part is fixed to the dome plate using M 3 socket-head cap screws. The length of the swashplate guide slot allows generous collective pitch travels to be exploited to the full; its position on the rotor shaft can be adjusted to...

Prezzo 14,70 €
Più
In vendita su richiesta
Swashplate guide black Anteprima

Riferimento: 52/10

Swashplate guide black

Recensioni: 0

For Schweizer 300 (Ord.No. 6031), Hughes 500 (Ord.No. 9005) and Agusta (Ord.No. 9020). Height of the slot 47.0 mm for use with the rotor shaft 35/39.

Prezzo 14,70 €
Più
In vendita su richiesta
Torna all'inizio

Seguici su Facebook

Facebook