Home

Filtra per

Disponibilità

Disponibilità

Prezzo

Prezzo

  • 5,00 € - 55,00 €

Categorie

Categorie

Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Tutte le migliori vendite

Ci sono 33 prodotti.

Ordina per:
Rilevanza Nome, da A a Z Nome, da Z ad A Prezzo, da meno caro a più caro Prezzo, da più caro a meno caro
Visualizzati 13-24 su 33 articoli

Filtri attivi

  • Categorie: Attrezzatura specifica
Glasspaper file, concave /... Anteprima

Riferimento: 11/56

Glasspaper file, concave / convex

Recensioni: 0

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Prezzo 12,80 €
Più
In vendita su richiesta
Tubing cutter, up to 15 mm Ø Anteprima

Riferimento: 11/60

Tubing cutter, up to 15 mm Ø

Recensioni: 0

The tubing cutter can handle aluminium, stainless steel and brass tubing up to 15 mm diameter. It can also be used to form a slight internal burr on tubing. For example if you use a tail rotor pushrod running in a PTFE sleeve in aluminium tubing, you can cut the aluminium to length at both ends with the tubing cutter, and the PTFE sleeve will not slip out.

Prezzo 33,30 €
Più
In vendita su richiesta
Hole cutter up to 16 mm Ø Anteprima

Riferimento: 11/64

Hole cutter up to 16 mm Ø

Recensioni: 0

There are far more holes to be drilled in a helicopter fuselage than just the ordinary air inlet holes. Think of the access holes for the needle valve and the glow plug, openings for the exhaust manifold and the initial stage of cutting window openings. This hole cutter does an excellent job. Hole cutter, up to 16 mm. Here a few hints for making perfect...

Prezzo 54,60 €
Più
In vendita su richiesta
Soft sanding paper Anteprima

Riferimento: 11/65

Soft sanding paper

Recensioni: 0

For preparing the GRP surface prior to the paintingP400dimensions: 11.5 x 15 cmPack of 5

Prezzo 9,70 €
Più
In vendita su richiesta
Pipe bending tool Anteprima

Riferimento: 11/80

Pipe bending tool

Recensioni: 0

A versatile bending tool for fuel tank pipes, dummy collective pitch sticks in the cockpit etc. The tool is useful for tubes or pushrods with a diameter of 3.0 and 3.2 mm

Prezzo 44,30 €
Più
In vendita su richiesta
Pushrod measuring holder Anteprima

Riferimento: 11/86

Pushrod measuring holder

Recensioni: 0

Model helicopter building instructions always state pushrod length as measured from ball centre to ball centre.Determining this dimension using conventional measuring tools is not really much more accurate than estimating the length.Pushrod measuring holderpack of 2holders fit any standard calipers

Prezzo 14,80 €
Più
In vendita su richiesta
Three-armed gripper Anteprima

Riferimento: 9/11

Three-armed gripper

Recensioni: 0

This handy three-armed gripper acts as a finger-extension for placing screws and nuts in difficult, small and inaccessible places.  Three-armed grippertotal length 115 mm

Prezzo 11,70 €
Più
In vendita su richiesta
Die M 2.5 HSS Anteprima

Riferimento: 70/20

Die M 2.5 HSS

Recensioni: 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prezzo 46,10 €
Più
In vendita su richiesta
Die M 2.0 HSS Anteprima

Riferimento: 70/21

Die M 2.0 HSS

Recensioni: 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prezzo 54,60 €
Più
In vendita su richiesta
Die M 3.0 HSS Anteprima

Riferimento: 70/22

Die M 3.0 HSS

Recensioni: 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prezzo 37,80 €
Più
In vendita su richiesta
Torna all'inizio

Seguici su Facebook

Facebook