LongRanger II 1:7 - Fuselage kit

Riferimento: 505/0

Foglio per decalcomanie Long Ranger II

Travi di coda in alluminio con spessore 0,8 mm sono realizzati in base alle richieste dei modelli trainer con motori a scoppio. I travi sono fabbricati in modo particolare, sono cioè controllati...

Riferimento: 506/30

Set di vetri Long Ranger II

 Long Ranger II glazing setclearnot trimmed

Riferimento: 3314/6

Conversione elettrica per SkyFox 1500 mm 6S

kit content:electric motor Kontronik Pyro 700-52 Lcontroller Kontronik JIVE 100+ LVmotor mounttoothed belt pulley 58 t. / 33 t.mounting materialKontronik TelMe can only be used with controllers Kontronik 120 JIVE Pro and higher.

Riferimento: 3309

Kit motore elettrico per meccanica X-treme 12S

Riferimento: 3309/12

Kit motore elettrico per meccanica X-treme 12S

Finestratura BK 117 trasparente da ritagliare

Riferimento: 35/24

Albero del rotore 10 x 234 mm

 Rotor shaftfor 2-bladed head

Riferimento: 35/38

L'asse del rotore 10 x 243 mm

Rotor shaftfor 2-bladed head

Riferimento: 1005/60

Testa del rotore a 3 pale 12 mm

Because of the high established demand on a rotor head being used in a mechanics driven by a petrol engine, the equipment is quite different from other rotor heads.Here flybars with 5 mm Ø are used, and the ball collets, the control bridge and the ballraces are applicable for this dimension. The aluminium centre piece accounts for the necessary precision...

Riferimento: 702/59

Toothed belt pulley 17-tooth XL Ø8mm

Not available

Riferimento: 29/10

Activator spray

For use with low or high viscosity cyano glue. Spray thinly over the glued joint and it sets the glue immediately. Content: 200 ml

Riferimento: 500/11

Stabiliser set Long Ranger

Stabiliser set, GRP5-partfor Long Ranger with a length up to approx. 1550 mm

Riferimento: 106/32

Tail cap Jet Ranger, Long Ranger

 Tail cap Jet Ranger and Long RangerGRP

Riferimento: 506/1

Skid landing gear for Long Ranger II

Riferimento: 506/3

Bulkhead set Long Ranger II

Component part for fuselage, Ord.No. 5006.

Riferimento: 1002/15

Electric "Skyfox" mechanics

Including metal internal tooth gear!These are the electric Skyfox mechanics which are used with one of the following conversion sets for the required gear ratio.Mechanics excludes motor, motor mount, and motor gears... see below.Following the trend for electric models, Vario have produced an electric conversion set for the popular Skyfox mechanics. The...

Riferimento: 1002/7

Mechanics set X-Treme

Not available

Riferimento: 403

2-blade-set 1550 mm

Specification2-blade-setlength: 660 mmrotor disc: 1550 mmblade root: 14 mm 1-holeblade chord: 62 mmprofile thickness: 7.5 mmweight: ca. 175 gmaterial: CFRPShark Skin finish: anthracite mattsymmetry: reflex l.h.r.

Riferimento: 407

2-blade-set 1500 mm

Specification2-blade-setlength: 660 mmrotor disc: 1500 mmblade root: 14 mm 1-holeblade chord: 62 mmprofile thickness: 7.5 mmweight: ca. 200 gmaterial: CFRPShark Skin finish: anthracite mattsymmetry: reflex l.h.r.

Riferimento: 33/2

Rotor blade pouch 2-blade Ø 2100 mm

bag length: 98 cmmax. blade width: 9.5 cm

Riferimento: 68/20

Swashplate driver 10 mm

Where a pitch compensator sits and two pushrods connect to the flybar, this is now a swashplate driver in its place.This is necessary to drive the inner ring of the swashplate in order to always control the blade angle in the same position.Aluminium swashplate driver with 4 ballraces.

Riferimento: 34/7

Tail rotor blades 102 mm, grey

Tail rotor blade, rotor disc 276 mm ØSpecification 8.0 mm blade root9.8 g approx.20-28 mm blade chordinj. moulded GRP3.5 mm profile thicknessdouble reflex102 mm longbalanced1 pair

Riferimento: 995

RC system accessories incl. 5 servos

If you already own a radio control system and then purchase a second model helicopter, the next step is to consider carefully which electronic components are the best choice for the new model.The combination illustrated here comprises accessories which have proved excellent in practice. RC system accessories, with Futaba BLS 452 servos excluding radio...

Riferimento: 871/100

Umbauset für X-Treme Elektro-Mechanik

Riferimento: 70/110-2

Gestänge 2,5 x 110 mmOrd.No. 70/110-2

Riferimento: 70/120-2

Gestänge 2,5 x 120 mmOrd.No. 70/120-2