Ennumerador de servo

Référence: 3936/1

Y-lead

If you want to operate two servos in parallel from one receiver channel you requires a Y-lead.

Référence: 330/18

Gear support for tail drive

Component part for fuselages like Air-Crane, Bell 47 or Lama.Pack of 3

Référence: 18/11

Aluminium tube 5.5 x 4.4 x 1000 mm

Aluminium tube 5.5 x 4.4 x 1000 mm

Référence: 3947

Quick-release servo mount

During construction we often need that "third hand", and there are times when it would be really useful to be able to see assemblies from front and rear at the same time.Servo installation is fast and reliable using the quick-release servo mount.The mounting plates are simply positioned either in front of the servo or behind it - whichever is more...

Référence: 330/10

Housse de protection pour Lama

This protective sheath provides effective protection to the cabin of your valuable helicopter, and helps to avoid unsightly scratches. It is simply pulled over the cabin and closed with a hook -and-loop fastener.Cabin sheath for Lamamatching the cabins of the models 3300 and 3400

Référence: 13/21

Magnets for speed regulator

These magnets are suitable for use with all commercial speed regulators. For installation in the mechanics it is advisable the magnets be glued in a clamp ring Ord.No. 54/6, or as in the photo on the internal-tooth gear ring. Pack of 3

Référence: 33/25

Porte pales pour transport

La bonne solution pour le transport: La découpe du grand support convient aux différentes formes des poutres sur les fuselages.Support de transportpour fuselages, 30 x 270 x 200 mm

Référence: 18

PVC tube 3.2 x 2.2 x 1000 mm, white

PVC tube 3.2 x 2.2 x 1000 mm, white

Référence: 21

Pushrod 1.5 x 1000 mm, steel

Pushrod 1.5 x 1000 mm, steel

Référence: 15/8

Charge lead MPX high current plug 2.5 mm²

Not available

Référence: 3942

Servo packer

Servo packing pieces are used with direct-linked JR / Graupner roll-axis servos to give clearance to the pitch-axis servo. Pack of 10

Référence: 33/6

Rotor blade pouch 2x3 blade max Ø 2100 mm

Référence: 97/9

Screw fitting pushrod connector

Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.Caution during installation: the barrel of the...

Référence: 3941/90

Servo mounting set

Rubber servo mounting grommets absorb vibration and also help to protect the servos.Servo mounting set, for 2 JR servos

Référence: 3944

Servo mount 120°

When using a 4-point-linkage, the linkages from the servos run in a straight line to the swashplate.A 3-point-linkage does not permit this, here the linkages run diagonally.The 120° servo mounting enables inclined installation of the servos, and the results are straight running linkages to the swashplate.All Sky Fox based mechanics as well as on the...

Référence: 33/27

Rotor blade tie-down large

The rotor blade harness ranks as an essential accessory for full-size helicopters. These items prevent the blades swinging or rocking, and thereby exerting pressure on the rotor shaft. If that were to be allowed, in-flight failures could be attributed to it.Rotor blades set in motion by rising winds could also be damaged by striking obstacles. The rotor...