Rotor Principal de 4 palas, 12 mm

Reference: 1005/59

Rotorkopf für TurbineOrd.No. 1005/59

Reference: 722/72

Rotor head VR-22

The loading of every component of this rotor system is designed to take a multiple of the actual forces. We are looking here at purely safety reserves and under no cirumstances should they be used for experimental purposes.Because of the special requirements of materials used in the rotor head, we expressly recommend that only genuine VARIO spare parts...

Reference: 705/37

5-blade rotor head 12 mm

Not available

Reference: 722/75

Conversion set for rotor head without flybar

This conversion set was originally developed for the Robinson R22 and Jet Ranger, but since then it has proved to be useful for a number of other large-scale models.Please note that the matching...

Reference: 702/62

Rigid 2 blade rotor head 12 mm

Not available

Reference: 1005/60

Rotor head petrol mechanics 10 mm

Because of the high established demand on a rotor head being used in a mechanics driven by a petrol engine, the equipment is quite different from other rotor heads.Here flybars with 5 mm Ø are used, and the ball collets, the control bridge and the ballraces are applicable for this dimension. The aluminium centre piece accounts for the necessary precision...

Reference: 704/36

4-blade rotor head 12 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 705/32

5-blade rotor head 12 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 1005/49

Rotor head up to 2500 mm for Bell 230 or AIRWOLFOrd.No. 1005/49

This rotor head is specially designed for the use with an AIRWOLF or a Bell 230.Rotor shaft 12 mm, rotor disc 2360 mmOrd.No. 1005/52 is for a Ø 15 mm rotor shaft and Ord.No. 1005/49 for a Ø 12 mm rotor shaft

Reference: 702/75

Semi scale rotor head

With the SKS semi-scale rotor head you will take the advantage of a mechanical gyro system with a delay in control commands caused by the flybar level.This system suits the scale looks of a UH-1D....

Reference: 705/30

5-blade rotor head 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 1005/52

Rotor head up to 2500 mmOrd.No. 1005/52

Ord.No. 1005/52 is for a Ø 15 mm rotor shaft and Ord.No. 1005/49 for Ø 12 mm rotor shaft

Reference: 1005/50

Sky Fox rotor head

The Sky Fox rotor head in its original form is robust and very sturdy, so it can achieve good results in all flight positions.The rotor head is supplied with a ball raced pitch compensator and two main shaft collars, their use depends on the length of the rotor shaft.CautionIt is not permissible to use this rotor head on a mechanical system powered by a...

Reference: 705/35

5-blade rotor head 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 704/35

4-blade rotor head, 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 1005/61

Rotor head petrol mechanics 12 mm

Because of the high established demand on a rotor head being used in a mechanics driven by a petrol engine, the equipment is quite different from other rotor heads.Here flybars with 5 mm Ø are used, and the ball collets, the control bridge and the ballraces are applicable for this dimension. The aluminium centre piece accounts for the necessary precision...