Accueil

Filtrer par

Motorisation

Motorisation

Disponibilité

Disponibilité

Poids

Poids

  • 0Kg - 10Kg

Prix

Prix

  • 0,00 € - 18 400,00 €

langage

langage

Type de rotor

Type de rotor

Motorization

Motorization

Catégories

Catégories

Marques

No brand

Fournisseurs
Meilleures Ventes
Flanged ballrace 6 x 10 x 3 mm Aperçu rapide

Référence: 92/91

Flanged ballrace 6 x 10 x 3 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prix 14,70 €
Détails
En vente sur demande
Toutes les meilleures ventes

Il y a 4961 produits.

Trier par :
Pertinence Nom, A à Z Nom, Z à A Prix, croissant Prix, décroissant
Affichage 1141-1152 de 4961 article(s)

Filtres actifs

Transport wheels for large... Aperçu rapide

Référence: 146

Transport wheels for large models

Commentaire(s): 0

The transport frames, Ord. No. 144 and 145, have proved excellent for moving large, heavy model helicopters around.However, wider wheels make them much more pleasant to use over certain types of terrain, and especially when the ground is wet.

Prix 108,30 €
Détails
En vente sur demande
Kit empennages carbone, laminé Aperçu rapide

Référence: 800/55

Kit empennages carbone, laminé

Commentaire(s): 0

Stabiliser set laminated of carbon2-part - extra lightweight!For installation at all trainers when the stabiliser holder Ord.No. 870/17 is present.250 mm high19.5 g total weight

Prix 62,80 €
Détails
En vente sur demande
Swashplate guide Aperçu rapide

Référence: 52/20

Swashplate guide

Commentaire(s): 0

The swashplate guide prevents the outer ring of the swashplate rotating; the swashplate pin runs in the slot in this guide. The part is fixed to the dome plate using M 3 socket-head cap screws. The length of the swashplate guide slot allows generous collective pitch travels to be exploited to the full; its position on the rotor shaft can be adjusted to...

Prix 14,70 €
Détails
En vente sur demande
Rotor blade allen key for... Aperçu rapide

Référence: 33/11

Rotor blade allen key for M5 socket-head screws

Commentaire(s): 0

Rotor blades for large-scale model helicopters must be secured using screws of the appropriate size. Normally M4 bolts are employed, but here the usual size is M5. The T-handle of this M5 allen key provides plenty of torque, but you should only tighten the screws to the point where the blades can still align themselves at start-up.

Prix 11,70 €
Détails
En vente sur demande
Lubricant set Aperçu rapide

Référence: 10/367

Lubricant set

Commentaire(s): 0

All mechanics require the correct lubrication: not too much and not too little. If friction is low, the rate of wear is reduced. This lubricant set includes both lubricants required for complete protection of the mechanics. When re-greasing check carefully that no grit is allowed into the lubricant (abrasive effect), and clean all parts before...

Prix 19,90 €
Détails
En vente sur demande
6 x 13 x 5 mm Aperçu rapide

Référence: 17/22

6 x 13 x 5 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 6 x 13 x 5 mmpack of...

Prix 11,20 €
Détails
En vente sur demande
Retour en haut

Suivez-nous sur Facebook

Facebook