Accueil
Marques

No brand

Fournisseurs
Meilleures Ventes
Flanged ballrace 6 x 10 x 3 mm Aperçu rapide

Référence: 92/91

Flanged ballrace 6 x 10 x 3 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prix 14,70 €
Détails
En vente sur demande
Toutes les meilleures ventes

Il y a 420 produits.

Trier par :
Pertinence Nom, A à Z Nom, Z à A Prix, croissant Prix, décroissant
Affichage 145-156 de 420 article(s)

Filtres actifs

PTFE tape 0.1 mm Aperçu rapide

Référence: 115/12

PTFE tape 0.1 mm

Commentaire(s): 0

To seal a fuel tank unscrew the cap and wrap 3 - 4 layers of PTFE tape round the threaded section. Screw the cap back on the tank as far as it will go.PTFE tape 0.1 mm12 mm wide, 12 m long

Prix 11,20 €
Détails
En vente sur demande
Tube PTFE 20 x 2,5 x 120 mm Aperçu rapide

Référence: 115/5

Tube PTFE 20 x 2,5 x 120 mm

Commentaire(s): 0

Manifolds and tuned pipes or silencers must be installed without touching each other, because the contact of these metal parts could cause radio interference. We can refer to this interference as "electric noise". The connection by PTFE pipe enables the required distance of 10 - 15 mm in the prescribed position, and it steadily seals gas-tight. This...

Prix 19,40 €
Détails
En vente sur demande
Systéme de remplissage pour... Aperçu rapide

Référence: 13/32

Systéme de remplissage pour kérosène

Commentaire(s): 0

The kerosene refuelling system is sealed with a rubber nipple. The constant low pressure inside the tank draws the nipple firmly against the refuelling opening. That is also the reason why a mechanism such as a spring-controlled valve is not suitable, because the low pressure tends to push the spring back as spring tension diminishes.

Prix 46,10 €
Détails
En vente sur demande
Tuned pipe silencer Aperçu rapide

Référence: 116/71

Tuned pipe silencer

Commentaire(s): 0

 Tuned pipe silenceroverall length 400 mmconnection-Ø 20 mmoverall Ø 40 mmsilencer chamber 240 mmweight approx. 180 gtail pipe length 100 mm

Prix 176,40 €
Détails
En vente sur demande
lining 45 x 40 x 12 mm Aperçu rapide

Référence: 64/8

lining 45 x 40 x 12 mm

Commentaire(s): 0

Friction between the flywheel and the clutch bell result in a certain amount of wear of the clutch lining.For installation you slightly grind one of the outer edges. Afterwards you press the liner with that edge in front into the clutch bell. To glue in a new clutch liner you use e.g. UHU plus endfest 300, Ord.No. 10/26 or 10/27.Fits the glow plug motor...

Prix 27,40 €
Détails
En vente sur demande
Swashplate driver 10 mm Aperçu rapide

Référence: 68/20

Swashplate driver 10 mm

Commentaire(s): 0

Where a pitch compensator sits and two pushrods connect to the flybar, this is now a swashplate driver in its place.This is necessary to drive the inner ring of the swashplate in order to always control the blade angle in the same position.Aluminium swashplate driver with 4 ballraces.

Prix 87,20 €
Détails
En vente sur demande
Exhaust for XL-C Aperçu rapide

Référence: 268/16

Exhaust for XL-C

Commentaire(s): 0

Exhaust tubes for turbines are always designed for the specified model. It is important that no forward thrust emerges from the system. Should this still occur, the forward thrust produced is minimal.Turbine exhaust tubes are designed as exhaust-gas diffusers, i.e. opens wider towards the rear.

Prix 254,50 €
Détails
En vente sur demande
Retour en haut

Suivez-nous sur Facebook

Facebook