Home

Filtra per

Disponibilità

Disponibilità

Prezzo

Prezzo

  • 5,00 € - 137,00 €

Categorie

Categorie

Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Aste 3,0 x 75 mm Anteprima

Riferimento: 70/76

Aste 3,0 x 75 mm

Recensioni: 0

Ready-made pushrod, threaded M 3. Content of the package: 1 piece

Prezzo 6,30 €
Più
In vendita su richiesta
Tutte le migliori vendite

Ci sono 60 prodotti.

Ordina per:
Rilevanza Nome, da A a Z Nome, da Z ad A Prezzo, da meno caro a più caro Prezzo, da più caro a meno caro
Visualizzati 13-24 su 60 articoli

Filtri attivi

  • Categorie: Attrezzatura specifica
  • Categorie: Attrezzi per il set-up
  • Categorie: Files, Perma Grit
Tool case Anteprima

Riferimento: 21/11

Tool case

Recensioni: 0

Tool case, complete empty, alone, including foam to cutsize approx. 275 x 230 x 83 mm

Prezzo 19,10 €
Più
In vendita su richiesta
Glazing panel shears straight Anteprima

Riferimento: 11/260

Glazing panel shears straight

Recensioni: 0

These powerful, sharp shears simplify the task of cutting out vacuum-moulded bodywork components. Glazing panels, dummy fuel tanks etc. are easily cut out along the moulded-in lines using these special shears. We suggest not to cut out anything until you satisfy yourself with the exact dimensions. This is because GRP parts (fuselages etc.) are hand made...

Prezzo 32,30 €
Più
In vendita su richiesta
Swashplate jig Anteprima

Riferimento: 68/4

Swashplate jig

Recensioni: 0

The pushrods from the swashplate to the rotor head must be set to identical lengths.Just slip the swashplate jig under the swashplate, and the swashplate will automatically be set parallel to the dome plate and at right-angles to the rotor shaft. You can now set up all your linkages with confidence.

Prezzo 19,40 €
Più
In vendita su richiesta
Glasspaper file, flat Anteprima

Riferimento: 11/28

Glasspaper file, flat

Recensioni: 0

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Prezzo 14,80 €
Più
In vendita su richiesta
Flybar spirit level Anteprima

Riferimento: 79/1

Flybar spirit level

Recensioni: 0

To adjust the pitch of the main rotor blades accurately it is essential to set the flybar exactly horizontal. This is done by simply hanging a spirit level from the flybar. But make sure that the helicopter is standing on a level surface before you start!

Prezzo 17,00 €
Più
In vendita su richiesta
Rotor head immobiliser Anteprima

Riferimento: 79/3

Rotor head immobiliser

Recensioni: 0

Working on the pitch adjustment of the main rotor blades requires a few conditions. First of all your helicopter must be standing on a flat level surface; the flybar must be horizontal and remain so throughout the procedure. The smooth running of all components with bearings makes this an almost impossible task because the slightest movement during pitch...

Prezzo 19,40 €
Più
In vendita su richiesta
Widia disc cutter Anteprima

Riferimento: 29/11

Widia disc cutter

Recensioni: 0

Widia produced a tungsten carbide, derived from "like diamond - Wie Diamant (Ger)". The first Widia tools were available on the open market in 1923. They consisted at that time of approx. 94 % tungsten carbide and 6 % cobalt. Today's types contain additives that improve the hardness etc. The Widia disc cutter is ideal for cutting clean-edged openings in...

Prezzo 16,90 €
Più
In vendita su richiesta
Rotor blade allen key for... Anteprima

Riferimento: 11/34

Rotor blade allen key for M6 socket-head screws

Recensioni: 0

Rotor blades for large-scale model helicopters must be secured using screws of the appropriate size. Normally M4 bolts are employed, but here the usual size is M6. The T-handle of this M6 allen key provides plenty of torque, but you should only tighten the screws to the point where the blades can still align themselves at start-up.

Prezzo 11,70 €
Più
In vendita su richiesta
Torna all'inizio

Seguici su Facebook

Facebook