Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Aste 3,0 x 75 mm Anteprima

Riferimento: 70/76

Aste 3,0 x 75 mm

Recensioni: 0

Ready-made pushrod, threaded M 3. Content of the package: 1 piece

Prezzo 6,30 €
Più
In vendita su richiesta
Tutte le migliori vendite

Set leva miscelatore

78/40
Valutazione 



Mixer levers are an essential part of every flybar-controlled rotor head. From the swashplate a pushrod runs to the ballraced mixer arm which is screwed to the blade holder arm. The mixer levers transmit the control movement to the flybar via the double ball-link.
Additionial accessories for the use of mixer levers are either two flanged ballraces or two flanged bushes from Delrin as a low cost alternative.
The screwing on the blade holder arm complies with the kind of hole, i.e. it depends on the through hole or on the blind hole.

Please note for choosing the screws: blade holder 76/15 = socket-head cap screw 90075, blade holder 76/13 = socket-head cap screw 90085 with self-locking nut 90530.

37,50 €
Tasse incluse
Quantità
In vendita su richiesta

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descrizione



Mixer levers are an essential part of every flybar-controlled rotor head. From the swashplate a pushrod runs to the ballraced mixer arm which is screwed to the blade holder arm. The mixer levers transmit the control movement to the flybar via the double ball-link.
Additionial accessories for the use of mixer levers are either two flanged ballraces or two flanged bushes from Delrin as a low cost alternative.
The screwing on the blade holder arm complies with the kind of hole, i.e. it depends on the through hole or on the blind hole.

Please note for choosing the screws: blade holder 76/15 = socket-head cap screw 90075, blade holder 76/13 = socket-head cap screw 90085 with self-locking nut 90530.

Dettagli del prodotto
78/40
Recensioni

Ancora nessuna recensione da parte degli utenti.

Scrivi la tua recensione

Set leva miscelatore

Set leva miscelatore



Mixer levers are an essential part of every flybar-controlled rotor head. From the swashplate a pushrod runs to the ballraced mixer arm which is screwed to the blade holder arm. The mixer levers transmit the control movement to the flybar via the double ball-link.
Additionial accessories for the use of mixer levers are either two flanged ballraces or two flanged bushes from Delrin as a low cost alternative.
The screwing on the blade holder arm complies with the kind of hole, i.e. it depends on the through hole or on the blind hole.

Please note for choosing the screws: blade holder 76/15 = socket-head cap screw 90075, blade holder 76/13 = socket-head cap screw 90085 with self-locking nut 90530.

Scrivi la tua recensione
16 autres produits dans la même catégorie :
Flybar stainless steel 4 x... Aperçu rapide

Référence: 79/21

Flybar stainless steel 4 x 320 mm

Commentaire(s): 0

The length of the flybar itself also plays an important role in the model's flight characteristics: the longer the flybar, the smoother the hover. A longer flybar increases the control deflections. 450 mm length is considered normal, while 510 mm provides more docile handling.

Prix 17,00 €
Détails
En vente sur demande
Barre de Bell inox 4 x 600 mm Aperçu rapide

Référence: 79/15

Barre de Bell inox 4 x 600 mm

Commentaire(s): 0

The length of the flybar itself also plays an important role in the model's flight characteristics: the longer the flybar, the smoother the hover. A longer flybar increases the control deflections. 450 mm length is considered normal, while 510 mm provides more docile handling.

Prix 19,40 €
Détails
En vente sur demande
O-ring 3 x 16 mm soft Aperçu rapide

Référence: 74/14

O-ring 3 x 16 mm soft

Commentaire(s): 0

O-ring 3 x 16 mm soft Content of the package: 8 pieces Tip: O-rings always slide with a drop of silicone oil onto the shaft.

Prix 6,30 €
Détails
En vente sur demande
Thrust bearing set complete Aperçu rapide

Référence: 117/20

Thrust bearing set complete

Commentaire(s): 0

The standard version of our mechanics includes ground thrust bearing shafts with a of 8 mm Ø and a length of 110 mm.Thrust bearings absorb the high centrifugal forces exerted by the main rotor blades. The effect of the axial bearings is retained in full when the blade holders rotate.Thrust bearing set, complete as shown.

Prix 54,60 €
Détails
En vente sur demande
Inertia weights for Ø 5 mm... Aperçu rapide

Référence: 79/8

Inertia weights for Ø 5 mm flybar

Commentaire(s): 0

Inertia weights are small "extra brakes". They increase the gyroscopic stability of the flybar and slow down the rotor head's response. For every beginner we recommend these so the responsiveness of the rotor head is reduced. The rotor head becomes more responsive as the inertia weights are moveded inwards (always place equally!). Inertia weights suitable...

Prix 30,60 €
Détails
En vente sur demande
Bearing pin Aperçu rapide

Référence: 68/19

Bearing pin

Commentaire(s): 0

Bearing pin for swashplate driver 68/20. Content of the package: 1 piece.

Prix 11,20 €
Détails
En vente sur demande
Rotor cap for Multi blade head Aperçu rapide

Référence: 707

Rotor cap for Multi blade head

Commentaire(s): 0

The diameter is 83 mm and the construction height from the screw-on surface to the highest point is 13 mm.It is fastened using an M4 x 14 hexagon socket screw (included).

Prix 30,60 €
Détails
En vente sur demande
Rotor brake, GRP Aperçu rapide

Référence: 72/5

Rotor brake, GRP

Commentaire(s): 0

When you have landed and stopped the engine, the rotor head continues spinning for quite some time until it stops by itself. A rotor brake shortens the time you have to wait. Using light pressure with the flat of your hand on the domed face of the rotor brake you can stop the rotor in a few moments.Please note: stay in safe distance away from the turning...

Prix 14,70 €
Détails
En vente sur demande
Ball collet 4 mm, short Aperçu rapide

Référence: 86/5

Ball collet 4 mm, short

Commentaire(s): 0

Ball collets provide the fixation of double ball-links on the flybar, in order to settle the essential distance to the rocker. Ball collet 4 mm Ø, overall length 19.7 mm, pack of 2, chrome-plated.

Prix 9,70 €
Détails
En vente sur demande

Seguici su Facebook

Facebook