Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Aste 3,0 x 75 mm Anteprima

Riferimento: 70/76

Aste 3,0 x 75 mm

Recensioni: 0

Ready-made pushrod, threaded M 3. Content of the package: 1 piece

Prezzo 6,30 €
Più
In vendita su richiesta
Tutte le migliori vendite

Rotor blade support

33/20
Valutazione 

An easy solution to the transport problem:
This rotor blade support fits all helicopter trainers with 20 mm O.D. tail booms.

  • Rotor blade support
  • for rotor blades up to 65 mm chord
14,70 €
Tasse incluse
Quantità
In vendita su richiesta

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descrizione

An easy solution to the transport problem:
This rotor blade support fits all helicopter trainers with 20 mm O.D. tail booms.

  • Rotor blade support
  • for rotor blades up to 65 mm chord
Dettagli del prodotto
33/20
Recensioni

Ancora nessuna recensione da parte degli utenti.

Scrivi la tua recensione

Rotor blade support

Rotor blade support

An easy solution to the transport problem:
This rotor blade support fits all helicopter trainers with 20 mm O.D. tail booms.

  • Rotor blade support
  • for rotor blades up to 65 mm chord
Scrivi la tua recensione
16 altri prodotti della stessa categoria:
GRP bracket Anteprima

Riferimento: 17/4

GRP bracket

Recensioni: 0

 Content of the package1 piece

Prezzo 12,80 €
Più
In vendita su richiesta
O-ring 3 x 8 mm hard Anteprima

Riferimento: 74

O-ring 3 x 8 mm hard

Recensioni: 0

O-ring 3 x 8 mm hard Content of the package: 4 pieces Tip: O-rings always slide with a drop of silicone oil onto the shaft.

Prezzo 5,40 €
Più
In vendita su richiesta
PTFE tube for tail drive shaft Anteprima

Riferimento: 18/10

PTFE tube for tail drive shaft

Recensioni: 0

PTFE is used as a bearing for the 2 mm wire tail drive shaft (Ord.No. 17) or as a support guide for the 2 mm piano wire push rod (Ord.No. 21 and 800/12) Length: approx. 740 mm

Prezzo 12,80 €
Più
In vendita su richiesta
Y-lead Anteprima

Riferimento: 3936/1

Y-lead

Recensioni: 0

If you want to operate two servos in parallel from one receiver channel you requires a Y-lead.

Prezzo 14,80 €
Più
In vendita su richiesta
Glue dispenser Anteprima

Riferimento: 10/75

Glue dispenser

Recensioni: 0

When you insert cartridges Ord.No. 10/73 into the dispenser and press the components through the mixing nozzle the epoxy is ready for immediate use.

Prezzo 49,80 €
Più
In vendita su richiesta
Magnets for speed regulator Anteprima

Riferimento: 13/21

Magnets for speed regulator

Recensioni: 0

These magnets are suitable for use with all commercial speed regulators. For installation in the mechanics it is advisable the magnets be glued in a clamp ring Ord.No. 54/6, or as in the photo on the internal-tooth gear ring. Pack of 3

Prezzo 11,70 €
Più
In vendita su richiesta

Seguici su Facebook

Facebook