Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Aste 3,0 x 75 mm Anteprima

Riferimento: 70/76

Aste 3,0 x 75 mm

Recensioni: 0

Ready-made pushrod, threaded M 3. Content of the package: 1 piece

Prezzo 6,30 €
Più
In vendita su richiesta
Tutte le migliori vendite

Servo extension lead 700 mm

3935/4
Valutazione 

When extending servo cables take into account that cable lengths over 500 mm requires a suppressor (Ord.No. 1040) to avoid interference.

9,70 €
Tasse incluse
Quantità
In vendita su richiesta

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descrizione

When extending servo cables take into account that cable lengths over 500 mm requires a suppressor (Ord.No. 1040) to avoid interference.

Dettagli del prodotto
3935/4
Recensioni

Ancora nessuna recensione da parte degli utenti.

Scrivi la tua recensione

Servo extension lead 700 mm

Servo extension lead 700 mm

When extending servo cables take into account that cable lengths over 500 mm requires a suppressor (Ord.No. 1040) to avoid interference.

Scrivi la tua recensione
16 altri prodotti della stessa categoria:
Servo mounting set Anteprima

Riferimento: 3941/90

Servo mounting set

Recensioni: 0

Rubber servo mounting grommets absorb vibration and also help to protect the servos.Servo mounting set, for 2 JR servos

Prezzo 11,70 €
Più
In vendita su richiesta
Rotor blade support Anteprima

Riferimento: 33/20

Rotor blade support

Recensioni: 0

An easy solution to the transport problem: This rotor blade support fits all helicopter trainers with 20 mm O.D. tail booms.Rotor blade supportfor rotor blades up to 65 mm chord

Prezzo 14,70 €
Più
In vendita su richiesta
Rotor blade tie-down large Anteprima

Riferimento: 33/27

Rotor blade tie-down large

Recensioni: 0

The rotor blade harness ranks as an essential accessory for full-size helicopters. These items prevent the blades swinging or rocking, and thereby exerting pressure on the rotor shaft. If that were to be allowed, in-flight failures could be attributed to it.Rotor blades set in motion by rising winds could also be damaged by striking obstacles. The rotor...

Prezzo 37,50 €
Più
In vendita su richiesta
Screw fitting pushrod... Anteprima

Riferimento: 97/9

Screw fitting pushrod connector

Recensioni: 0

Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.Caution during installation: the barrel of the...

Prezzo 6,30 €
Più
In vendita su richiesta
PTFE tube for tail drive shaft Anteprima

Riferimento: 18/10

PTFE tube for tail drive shaft

Recensioni: 0

PTFE is used as a bearing for the 2 mm wire tail drive shaft (Ord.No. 17) or as a support guide for the 2 mm piano wire push rod (Ord.No. 21 and 800/12) Length: approx. 740 mm

Prezzo 12,80 €
Più
In vendita su richiesta
Servo linkage set Anteprima

Riferimento: 97/4

Servo linkage set

Recensioni: 0

When you build your first model helicopter you will find all the linkage components required to connect the servos to the mechanics supplied with the RC set (German radio systems only). When you come to installing servos in other models you can use this servo linkage set which contains all the link balls, screws, nuts and screw-fitting pushrod...

Prezzo 46,10 €
Più
In vendita su richiesta

Seguici su Facebook

Facebook