Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Aste 3,0 x 75 mm Anteprima

Riferimento: 70/76

Aste 3,0 x 75 mm

Recensioni: 0

Ready-made pushrod, threaded M 3. Content of the package: 1 piece

Prezzo 6,30 €
Più
In vendita su richiesta
Tutte le migliori vendite

Helmet for pilot William

1/21
Valutazione 

As you would expect, we can also supply the matching type of GRP helmet for William the Pilot; it is simply pushed into place on his head.

If you wish to fit a radio headpiece, you now have plenty of scope for your imagination: a piece of foam rubber, a thin wire mount and a coiled cable are all you need to make this accessory, and the pilot will appreciate the ability to communicate properly.

32,60 €
Tasse incluse
Quantità
In vendita su richiesta

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descrizione

As you would expect, we can also supply the matching type of GRP helmet for William the Pilot; it is simply pushed into place on his head.

If you wish to fit a radio headpiece, you now have plenty of scope for your imagination: a piece of foam rubber, a thin wire mount and a coiled cable are all you need to make this accessory, and the pilot will appreciate the ability to communicate properly.

Dettagli del prodotto
1/21
Recensioni

Ancora nessuna recensione da parte degli utenti.

Scrivi la tua recensione

Helmet for pilot William

Helmet for pilot William

As you would expect, we can also supply the matching type of GRP helmet for William the Pilot; it is simply pushed into place on his head.

If you wish to fit a radio headpiece, you now have plenty of scope for your imagination: a piece of foam rubber, a thin wire mount and a coiled cable are all you need to make this accessory, and the pilot will appreciate the ability to communicate properly.

Scrivi la tua recensione
16 altri prodotti della stessa categoria:
Set accessori portelli per... Anteprima

Riferimento: 330/5

Set accessori portelli per Bell 47 G III, Lama

Recensioni: 0

Door fittings for large-scale model helicopters do not differ fundamentally from one type to another. However, the size of these accessories is important if the model is to look convincing, otherwise they will look out of scale.Compare the door handle of the Lama with that of the Alouette II, and the difference is obvious.The door fittings set for the...

Prezzo 46,10 €
Più
In vendita su richiesta
Imitazione turbina Anteprima

Riferimento: 330/2

Imitazione turbina

Recensioni: 0

The dummy turbine provides the ideal starting point if you wish to install additional scale fittings on your Lama.The dummy turbine is assembled from six separate GRP mouldings, and fits all models with VR-22 mechanics installed.In the turbine-powered version of the Lama the actual turbine is located in this position.GRP dummy turbineLength approx. 490 mm

Prezzo 141,80 €
Più
In vendita su richiesta
Estintore, lunghezza ca. 70mm Anteprima

Riferimento: 30/50

Estintore, lunghezza ca. 70mm

Recensioni: 0

Fire extinguishers in the cockpit are mandatory for any scale model helicopter, since the full-size machines are also required to carry them.Our fire extinguisher is available in two different sizes, and it can be mounted in the cockpit in a wide variety of positions.For models up to 2000 mm rotor diameter we recommend the smaller version; the bigger one...

Prezzo 30,60 €
Più
In vendita su richiesta
Pedana di salita per Lama Anteprima

Riferimento: 340/6

Pedana di salita per Lama

Recensioni: 0

If you have a mind to continue adding detail fittings to your Lama, you are sure to appreciate this landing gear step which can be fitted to an existing model at any time. The step is made of stainless steel, and is supplied complete with clips, screw fittings and tread material. Entry step, for Lama, pack of 1

Prezzo 75,60 €
Più
In vendita su richiesta
Finta trasmissione Anteprima

Riferimento: 340/13

Finta trasmissione

Recensioni: 0

This dummy power unit can be installed on turbine powered helicopters to produce an even more realistic intersection between the turbine and the gearbox.When the imitation rotor brake of the dummy part is pushed over the turbine starter, the rubber connector is spring-loaded in front of the gearbox connection; retaining screws are not required.Dummy power...

Prezzo 133,60 €
Più
In vendita su richiesta
Supporti ruota per Lama Anteprima

Riferimento: 340/1

Supporti ruota per Lama

Recensioni: 0

The Lama is a large helicopter, and the supplementary wheels which can be attached to the landing gear make it much easier to move the machine into and out of the hangar. However, the wheels are removed prior to flying the model. These wheel holders for our model of the Lama are made of plastic and are simply glued to the 20 mm Ø skid tubes using UHU...

Prezzo 46,10 €
Più
In vendita su richiesta

Seguici su Facebook