Stainless steel manifold 42 mm

Riferimento: 7/17

6 x 16 x 5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 6 x 16 x 5 mmpack of...

Riferimento: 55/3

Thrust bearing 10 x 25 x 6 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence.The dimensions of a ballrace mean:inside diameter (I.D.) x outside diameter (O.D.) x thickness.Thrust bearing 10 x 25 x 6...

Riferimento: 17/22

6 x 13 x 5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 6 x 13 x 5 mmpack of...

Riferimento: 11/22

Magnetiser

Everyone has experienced the annoyance of small screws which won't stay on the screwdriver. This magnetiser solves the problem. It is a small, handy unit which will magnetise any screwdriver, and the screw will then stick to it. You simply place the screwdriver in the "+" socket and move it to and from. To de-magnetise it repeat the procedure in the "-"...

Riferimento: 68/2

20 x 32 x 7 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 20 x 32 x 7 mmpack of 1 

Riferimento: 11/62

Crankshaft nut socket spanner 13 mm

If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 13 mm, for Rossi or Webra

Riferimento: 94/17

Thrust bearing 7 x 13 x 4.5 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 7 x 13 x 4.5...

Riferimento: 870/49

Servo frame CFK

Riferimento: 11/67

Crankshaft nut socket spanner 14 mm

If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 14 mm, for O.S. 4-stroke

Riferimento: 58/11

3 x 8 x 3 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 3 x 8 x 3 mmpack of...

Riferimento: 94/3

Thrust bearing 4 x 10 x 3 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 4 x 10 x 3...

Riferimento: 116/94

Silencer for 116/95

Silencer, aloneIntake pipe 170 mmSilencer chamber 195 mmOverall Ø 50 mm

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Riferimento: 116/98

Manifold 34 mm

The various exhaust manifolds differ in shape and in the size of the flange, to match different engines' exhaust stubs. The term "exhaust hole spacing" refers to the holes on either side of the exhaust port, measured between hole centres.Please check before you order that you have selected the correct manifold to match your model and engine. Measure again...

Riferimento: 830/42

Exhaust mount 42 mm

  For silencer Ord.No. 116/96.Content of the package1 piece

Riferimento: 11/66

Crankshaft nut socket spanner 10 mm

If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 10 mm, for O.S.