Rotor blade allen key for M6 socket-head screws

Riferimento: 830/2

Extractor screw

Extractor screwkey size 13for flywheel and split tapper collet on petrol engines

Riferimento: 11/86

Pushrod measuring holder

Model helicopter building instructions always state pushrod length as measured from ball centre to ball centre.Determining this dimension using conventional measuring tools is not really much more accurate than estimating the length.Pushrod measuring holderpack of 2holders fit any standard calipers

Riferimento: 11/28

Glasspaper file, flat

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Riferimento: 107/2

Ball-link driver 4.0

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverfor 4 mm telescopic handle.

Riferimento: 11/59

Juego de herramientas de corte (bisturí + regla)

Riferimento: 10/77

Sanding sponge

The primary use for abrasive sponges is for large-area sanding of wooden and GRP components, but they are also excellent for rubbing down filled surfaces when used wet. Abrasive sponges are also useful for fine-sanding of components with sharp edges and rounded surfaces.

Riferimento: 11/65

Soft sanding paper

For preparing the GRP surface prior to the paintingP400dimensions: 11.5 x 15 cmPack of 5

Riferimento: 90/7

Hammer, weight 230 g

How do you fix anything to a wooden component using a metric machine screw? The answer is to fit a captive nut as follows: Drill a hole of the right size to accept the nut barrel, then drive the nut's projecting teeth into the wood using a hammer and fairly gentle force; the captive nut is correctly fitted when its disc rests squarely on the surface of...

Riferimento: 107/0

Ball-link driver with handle

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverwith telescopic handle 11/44

Riferimento: 11/64

Hole cutter up to 16 mm Ø

There are far more holes to be drilled in a helicopter fuselage than just the ordinary air inlet holes. Think of the access holes for the needle valve and the glow plug, openings for the exhaust manifold and the initial stage of cutting window openings. This hole cutter does an excellent job. Hole cutter, up to 16 mm. Here a few hints for making perfect...

Riferimento: 11/56

Glasspaper file, concave / convex

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Riferimento: 111/11

Handle for socket spanners Ø 6mm

Not available

Riferimento: 34/9

Tail blade balance shaft

If the tail rotor blades are to be balanced accurately, the assembled hub must be included in the balance process. Now you can balance the tail rotor perfectly, and the unit's smooth running will prove it!

Riferimento: 29/11

Widia disc cutter

Widia produced a tungsten carbide, derived from "like diamond - Wie Diamant (Ger)". The first Widia tools were available on the open market in 1923. They consisted at that time of approx. 94 % tungsten carbide and 6 % cobalt. Today's types contain additives that improve the hardness etc. The Widia disc cutter is ideal for cutting clean-edged openings in...

Riferimento: 9/5

Protective goggles

When handling tools it is in your own interests to read and observe the safety information and constantly to be aware of the possible hazards, before you have a really close encounter with a workpiece which, for whatever reason, flies off. Wear these protective goggles when grinding, turning and machining, and also when you are cutting off steel rod....

Riferimento: 11/44

Handle for socket spanners Ø 4mm

Accessories for the fine-point screwdriver set Ord.No. 11/39 are also available separately.