Handle for socket spanners Ø 6mm

Référence: 21/11

Tool case

Tool case, complete empty, alone, including foam to cutsize approx. 275 x 230 x 83 mm

Référence: 10/77

Sanding sponge

The primary use for abrasive sponges is for large-area sanding of wooden and GRP components, but they are also excellent for rubbing down filled surfaces when used wet. Abrasive sponges are also useful for fine-sanding of components with sharp edges and rounded surfaces.

Référence: 34/9

Tail blade balance shaft

If the tail rotor blades are to be balanced accurately, the assembled hub must be included in the balance process. Now you can balance the tail rotor perfectly, and the unit's smooth running will prove it!

Référence: 11/65

Soft sanding paper

For preparing the GRP surface prior to the paintingP400dimensions: 11.5 x 15 cmPack of 5

Référence: 11/60

Tubing cutter, up to 15 mm Ø

The tubing cutter can handle aluminium, stainless steel and brass tubing up to 15 mm diameter. It can also be used to form a slight internal burr on tubing. For example if you use a tail rotor pushrod running in a PTFE sleeve in aluminium tubing, you can cut the aluminium to length at both ends with the tubing cutter, and the PTFE sleeve will not slip out.

Référence: 11/36

Disc cutter set

Disc cutter set pack of 5 normal variation Wear protective goggles!

Référence: 107/2

Ball-link driver 4.0

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverfor 4 mm telescopic handle.

Référence: 90/10

File set with handle, six-part

This special file set is particularly useful when you are cutting small openings, as they can be used to work on the tiniest of radii and straight edges. The rotary-action handle makes quick work of swapping individual tools. The collet can also be used to grip drills and taps of 2 to 5 mm ∅.

Référence: 9/11

Three-armed gripper

This handy three-armed gripper acts as a finger-extension for placing screws and nuts in difficult, small and inaccessible places.  Three-armed grippertotal length 115 mm

Référence: 11/26

Cizallas para paneles de acristalamiento

Référence: 9/5

Protective goggles

When handling tools it is in your own interests to read and observe the safety information and constantly to be aware of the possible hazards, before you have a really close encounter with a workpiece which, for whatever reason, flies off. Wear these protective goggles when grinding, turning and machining, and also when you are cutting off steel rod....

Référence: 11/56

Glasspaper file, concave / convex

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Référence: 70/22

Die M 3.0 HSS

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Référence: 11/80

Pipe bending tool

A versatile bending tool for fuel tank pipes, dummy collective pitch sticks in the cockpit etc. The tool is useful for tubes or pushrods with a diameter of 3.0 and 3.2 mm

Référence: 107/1

Ball-link driver 5.5

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverfor 5.5 mm socket spanner

Référence: 11/64

Hole cutter up to 16 mm Ø

There are far more holes to be drilled in a helicopter fuselage than just the ordinary air inlet holes. Think of the access holes for the needle valve and the glow plug, openings for the exhaust manifold and the initial stage of cutting window openings. This hole cutter does an excellent job. Hole cutter, up to 16 mm. Here a few hints for making perfect...