Home

Filtra per

Disponibilità

Disponibilità

Prezzo

Prezzo

  • 5,00 € - 131,00 €

Categorie

Categorie

Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Aste 3,0 x 75 mm Anteprima

Riferimento: 70/76

Aste 3,0 x 75 mm

Recensioni: 0

Ready-made pushrod, threaded M 3. Content of the package: 1 piece

Prezzo 6,30 €
Più
In vendita su richiesta
Tutte le migliori vendite

Ci sono 40 prodotti.

Ordina per:
Rilevanza Nome, da A a Z Nome, da Z ad A Prezzo, da meno caro a più caro Prezzo, da più caro a meno caro
Visualizzati 13-24 su 40 articoli

Filtri attivi

  • Categorie: Attrezzatura specifica
  • Categorie: Attrezzi per il set-up
Rotor head immobiliser Anteprima

Riferimento: 79/3

Rotor head immobiliser

Recensioni: 0

Working on the pitch adjustment of the main rotor blades requires a few conditions. First of all your helicopter must be standing on a flat level surface; the flybar must be horizontal and remain so throughout the procedure. The smooth running of all components with bearings makes this an almost impossible task because the slightest movement during pitch...

Prezzo 19,40 €
Più
In vendita su richiesta
Widia disc cutter Anteprima

Riferimento: 29/11

Widia disc cutter

Recensioni: 0

Widia produced a tungsten carbide, derived from "like diamond - Wie Diamant (Ger)". The first Widia tools were available on the open market in 1923. They consisted at that time of approx. 94 % tungsten carbide and 6 % cobalt. Today's types contain additives that improve the hardness etc. The Widia disc cutter is ideal for cutting clean-edged openings in...

Prezzo 16,90 €
Più
In vendita su richiesta
Flybar jig Anteprima

Riferimento: 91/1

Flybar jig

Recensioni: 0

A flybar rotor head is controlled indirectly; movements are transmitted first to the flybar and paddles (Hiller control method, using auxiliary rotor head). The Hiller system only works perfectly if the paddles are set exactly parallel to each other. Unevenly set paddles also produce a bending moment on the flybar during every rotation which leads to more...

Prezzo 27,40 €
Più
In vendita su richiesta
Rotor blade allen key for... Anteprima

Riferimento: 11/34

Rotor blade allen key for M6 socket-head screws

Recensioni: 0

Rotor blades for large-scale model helicopters must be secured using screws of the appropriate size. Normally M4 bolts are employed, but here the usual size is M6. The T-handle of this M6 allen key provides plenty of torque, but you should only tighten the screws to the point where the blades can still align themselves at start-up.

Prezzo 11,70 €
Più
In vendita su richiesta
Disc cutter set Anteprima

Riferimento: 11/36

Disc cutter set

Recensioni: 0

Disc cutter set pack of 5 normal variation Wear protective goggles!

Prezzo 6,60 €
Più
In vendita su richiesta
Ridge cutter Anteprima

Riferimento: 11/53

Ridge cutter

Recensioni: 0

Use this small ridge cutter to remove sharp burrs and edges from aluminium and plastics; e.g. remove sharp edges from an aluminium pipe.

Prezzo 14,80 €
Più
In vendita su richiesta
Glasspaper file, concave /... Anteprima

Riferimento: 11/56

Glasspaper file, concave / convex

Recensioni: 0

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Prezzo 12,80 €
Più
In vendita su richiesta
Tubing cutter, up to 15 mm Ø Anteprima

Riferimento: 11/60

Tubing cutter, up to 15 mm Ø

Recensioni: 0

The tubing cutter can handle aluminium, stainless steel and brass tubing up to 15 mm diameter. It can also be used to form a slight internal burr on tubing. For example if you use a tail rotor pushrod running in a PTFE sleeve in aluminium tubing, you can cut the aluminium to length at both ends with the tubing cutter, and the PTFE sleeve will not slip out.

Prezzo 33,30 €
Più
In vendita su richiesta
Hole cutter up to 16 mm Ø Anteprima

Riferimento: 11/64

Hole cutter up to 16 mm Ø

Recensioni: 0

There are far more holes to be drilled in a helicopter fuselage than just the ordinary air inlet holes. Think of the access holes for the needle valve and the glow plug, openings for the exhaust manifold and the initial stage of cutting window openings. This hole cutter does an excellent job. Hole cutter, up to 16 mm. Here a few hints for making perfect...

Prezzo 54,60 €
Più
In vendita su richiesta
Soft sanding paper Anteprima

Riferimento: 11/65

Soft sanding paper

Recensioni: 0

For preparing the GRP surface prior to the paintingP400dimensions: 11.5 x 15 cmPack of 5

Prezzo 9,70 €
Più
In vendita su richiesta
Torna all'inizio

Seguici su Facebook

Facebook