Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Aste 3,0 x 75 mm Anteprima

Riferimento: 70/76

Aste 3,0 x 75 mm

Recensioni: 0

Ready-made pushrod, threaded M 3. Content of the package: 1 piece

Prezzo 6,30 €
Più
In vendita su richiesta
Tutte le migliori vendite

Bielle Hiller a 90°

87/4
Valutazione 


A 90° twisted double ball-link connect the mixer lever to the ball collet on the flybar.

Content of the package: 2 pieces
11,20 €
Tasse incluse
Quantità
In vendita su richiesta

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descrizione


A 90° twisted double ball-link connect the mixer lever to the ball collet on the flybar.

Content of the package: 2 pieces
Dettagli del prodotto
87/4
Recensioni

Ancora nessuna recensione da parte degli utenti.

Scrivi la tua recensione

Bielle Hiller a 90°

Bielle Hiller a 90°



A 90° twisted double ball-link connect the mixer lever to the ball collet on the flybar.

Content of the package: 2 pieces
Scrivi la tua recensione
16 altri prodotti della stessa categoria:
CFRP plates for aluminium hub Anteprima

Riferimento: 72/42

CFRP plates for aluminium hub

Recensioni: 0

This rotor head hub with its bonded-in carbon fibre plates is a real head-turner. The plates are simply glued into the existing recesses on both sides. We recommend silicone rubber, Ord.No. 10/11, as adhesive.CFRP plates for aluminium hub matching Ord.No. 832/72pack quantity: 2 plates

Prezzo 17,00 €
Più
In vendita su richiesta
GRP blade holder, 22 mm... Anteprima

Riferimento: 702/76

GRP blade holder, 22 mm blade throat

Recensioni: 0

This blade holder was specially developed for the large Bell 47 G III with a rotor diameter of 2.36 m. It has a 22 mm blade throat and a 6 mm Ø bore for the retaining screw, i.e. the matching blade holder screws and self-locking nuts are M6 in size.

Prezzo 37,80 €
Più
In vendita su richiesta
Rotor head dampers for 2... Anteprima

Riferimento: 74/7

Rotor head dampers for 2 blade FBL systems

Recensioni: 0

Flybarless electronics have now become common. Where they are being used harder damping is required.For these cases Vario is now offering a harder damping of the blade shaft provided by a pretension absorbing element in the centre block.For the adjustment, the outer O-ring position can be selected between "hard" and "soft" flight characteristics.Important...

Prezzo 30,60 €
Più
In vendita su richiesta
Thrust washer Anteprima

Riferimento: 832/75

Thrust washer

Recensioni: 0

Thrust washer for rotor head Content of the package: 2 pieces

Prezzo 13,50 €
Più
In vendita su richiesta
Paddles Anteprima

Riferimento: 91/60

Paddles

Recensioni: 0

 Paddles1 pairapprox. 29 g eachfor 4 mm Ø flybar

Prezzo 27,40 €
Più
In vendita su richiesta
Mixer lever cranked Anteprima

Riferimento: 78/41

Mixer lever cranked

Recensioni: 0

Mixer lever, content of the package 1 piece.Additionial accessories for the use of mixer levers are either two flanged ballraces or two flanged bushes from Delrin as a low cost alternative. The screwing on the blade holder arm complies with the kind of hole, i.e. it depends on the through hole or on the blind hole. Please note for choosing the screws:...

Prezzo 17,00 €
Più
In vendita su richiesta

Seguici su Facebook

Facebook