Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Tutte le migliori vendite

Rotor blade tie-down

33/28
Valutazione 

Rotor blade tie-downs are an essential feature of full-size helicopter life. The tie-down protects the blades from swinging, rocking and stretching, and thereby prevents excessive pressure on the rotor shaft. If these measures were not taken the result could easily be in-flight mechanical failure; rotor blades spinning as the wind rises could strike obstacles and be damaged.
For safety and to keep the helicopter ready for flight the rotor blade tie-down is attached to the tail boom and / or the skid tubes.
The tie-down makes an attractive accessory for decorating your model helicopter in the pits.

  • Rotor blade tie-down
  • pack of 1
  • up to 75 mm blade chord
30,60 €
Tasse incluse
Quantità
In vendita su richiesta

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descrizione

Rotor blade tie-downs are an essential feature of full-size helicopter life. The tie-down protects the blades from swinging, rocking and stretching, and thereby prevents excessive pressure on the rotor shaft. If these measures were not taken the result could easily be in-flight mechanical failure; rotor blades spinning as the wind rises could strike obstacles and be damaged.
For safety and to keep the helicopter ready for flight the rotor blade tie-down is attached to the tail boom and / or the skid tubes.
The tie-down makes an attractive accessory for decorating your model helicopter in the pits.

  • Rotor blade tie-down
  • pack of 1
  • up to 75 mm blade chord
Dettagli del prodotto
33/28
Recensioni

Ancora nessuna recensione da parte degli utenti.

Scrivi la tua recensione

Rotor blade tie-down

Rotor blade tie-down

Rotor blade tie-downs are an essential feature of full-size helicopter life. The tie-down protects the blades from swinging, rocking and stretching, and thereby prevents excessive pressure on the rotor shaft. If these measures were not taken the result could easily be in-flight mechanical failure; rotor blades spinning as the wind rises could strike obstacles and be damaged.
For safety and to keep the helicopter ready for flight the rotor blade tie-down is attached to the tail boom and / or the skid tubes.
The tie-down makes an attractive accessory for decorating your model helicopter in the pits.

  • Rotor blade tie-down
  • pack of 1
  • up to 75 mm blade chord
Scrivi la tua recensione
16 autres produits dans la même catégorie :
Servo packer Aperçu rapide

Référence: 3942

Servo packer

Commentaire(s): 0

Servo packing pieces are used with direct-linked JR / Graupner roll-axis servos to give clearance to the pitch-axis servo. Pack of 10

Prix 9,40 €
Détails
En vente sur demande
Rotor blade support Aperçu rapide

Référence: 33/22

Rotor blade support

Commentaire(s): 0

If you do not wish to remove the rotor blades temporarily for transport, they can be protected effectively in this strong support, which is mounted above the tail boom.The height of the support, the width of the blade openings and the diameter of the tail boom are the crucial factors when buying a blade support.This support is ideal for pod-and-boom...

Prix 17,00 €
Détails
En vente sur demande
O-ring 3 x 8 mm hard Aperçu rapide

Référence: 74

O-ring 3 x 8 mm hard

Commentaire(s): 0

O-ring 3 x 8 mm hard Content of the package: 4 pieces Tip: O-rings always slide with a drop of silicone oil onto the shaft.

Prix 5,40 €
Détails
En vente sur demande
PTFE tube for tail drive shaft Aperçu rapide

Référence: 18/10

PTFE tube for tail drive shaft

Commentaire(s): 0

PTFE is used as a bearing for the 2 mm wire tail drive shaft (Ord.No. 17) or as a support guide for the 2 mm piano wire push rod (Ord.No. 21 and 800/12) Length: approx. 740 mm

Prix 12,80 €
Détails
En vente sur demande
Glue dispenser Aperçu rapide

Référence: 10/75

Glue dispenser

Commentaire(s): 0

When you insert cartridges Ord.No. 10/73 into the dispenser and press the components through the mixing nozzle the epoxy is ready for immediate use.

Prix 49,80 €
Détails
En vente sur demande
Quick-release servo mount Aperçu rapide

Référence: 3947

Quick-release servo mount

Commentaire(s): 0

During construction we often need that "third hand", and there are times when it would be really useful to be able to see assemblies from front and rear at the same time.Servo installation is fast and reliable using the quick-release servo mount.The mounting plates are simply positioned either in front of the servo or behind it - whichever is more...

Prix 9,80 €
Détails
En vente sur demande
Servo linkage set Aperçu rapide

Référence: 97/4

Servo linkage set

Commentaire(s): 0

When you build your first model helicopter you will find all the linkage components required to connect the servos to the mechanics supplied with the RC set (German radio systems only). When you come to installing servos in other models you can use this servo linkage set which contains all the link balls, screws, nuts and screw-fitting pushrod...

Prix 46,10 €
Détails
En vente sur demande

Seguici su Facebook

Facebook