Accueil

Filtrer par

Disponibilité

Disponibilité

Prix

Prix

  • 5,00 € - 131,00 €

Catégories

Catégories

Marques

No brand

Fournisseurs
Meilleures Ventes
Flanged ballrace 6 x 10 x 3 mm Aperçu rapide

Référence: 92/91

Flanged ballrace 6 x 10 x 3 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prix 14,70 €
Détails
En vente sur demande
Toutes les meilleures ventes
Outillages/colles/lubrifiants

Outillages/colles/lubrifiants

Outillages/colles/lubrifiants

Il y a 36 produits.

Trier par :
Pertinence Nom, A à Z Nom, Z à A Prix, croissant Prix, décroissant
Affichage 1-12 de 36 article(s)

Filtres actifs

  • Disponibilité : En stock
  • Catégories : Accessoires spécifiques
  • Catégories : Gabarits
Sanding sponge Aperçu rapide

Référence: 10/77

Sanding sponge

Commentaire(s): 0

The primary use for abrasive sponges is for large-area sanding of wooden and GRP components, but they are also excellent for rubbing down filled surfaces when used wet. Abrasive sponges are also useful for fine-sanding of components with sharp edges and rounded surfaces.

Prix 5,50 €
Détails
En vente sur demande
Ball-link driver 5.5 Aperçu rapide

Référence: 107/1

Ball-link driver 5.5

Commentaire(s): 0

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverfor 5.5 mm socket spanner

Prix 8,40 €
Détails
En vente sur demande
Ball-link driver 4.0 Aperçu rapide

Référence: 107/2

Ball-link driver 4.0

Commentaire(s): 0

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverfor 4 mm telescopic handle.

Prix 8,40 €
Détails
En vente sur demande
Tool case Aperçu rapide

Référence: 21/11

Tool case

Commentaire(s): 0

Tool case, complete empty, alone, including foam to cutsize approx. 275 x 230 x 83 mm

Prix 19,10 €
Détails
En vente sur demande
Glazing panel shears straight Aperçu rapide

Référence: 11/260

Glazing panel shears straight

Commentaire(s): 0

These powerful, sharp shears simplify the task of cutting out vacuum-moulded bodywork components. Glazing panels, dummy fuel tanks etc. are easily cut out along the moulded-in lines using these special shears. We suggest not to cut out anything until you satisfy yourself with the exact dimensions. This is because GRP parts (fuselages etc.) are hand made...

Prix 32,30 €
Détails
En vente sur demande
Glasspaper file, flat Aperçu rapide

Référence: 11/28

Glasspaper file, flat

Commentaire(s): 0

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Prix 14,80 €
Détails
En vente sur demande
Flybar spirit level Aperçu rapide

Référence: 79/1

Flybar spirit level

Commentaire(s): 0

To adjust the pitch of the main rotor blades accurately it is essential to set the flybar exactly horizontal. This is done by simply hanging a spirit level from the flybar. But make sure that the helicopter is standing on a level surface before you start!

Prix 17,00 €
Détails
En vente sur demande
Widia disc cutter Aperçu rapide

Référence: 29/11

Widia disc cutter

Commentaire(s): 0

Widia produced a tungsten carbide, derived from "like diamond - Wie Diamant (Ger)". The first Widia tools were available on the open market in 1923. They consisted at that time of approx. 94 % tungsten carbide and 6 % cobalt. Today's types contain additives that improve the hardness etc. The Widia disc cutter is ideal for cutting clean-edged openings in...

Prix 16,90 €
Détails
En vente sur demande
Rotor head immobiliser Aperçu rapide

Référence: 79/3

Rotor head immobiliser

Commentaire(s): 0

Working on the pitch adjustment of the main rotor blades requires a few conditions. First of all your helicopter must be standing on a flat level surface; the flybar must be horizontal and remain so throughout the procedure. The smooth running of all components with bearings makes this an almost impossible task because the slightest movement during pitch...

Prix 19,40 €
Détails
En vente sur demande
Flybar jig Aperçu rapide

Référence: 91/1

Flybar jig

Commentaire(s): 0

A flybar rotor head is controlled indirectly; movements are transmitted first to the flybar and paddles (Hiller control method, using auxiliary rotor head). The Hiller system only works perfectly if the paddles are set exactly parallel to each other. Unevenly set paddles also produce a bending moment on the flybar during every rotation which leads to more...

Prix 27,40 €
Détails
En vente sur demande
Retour en haut

Suivez-nous sur Facebook

Facebook