Filtro, Lama 1:4

Référence: 10/96

Anti-collision light with red housing

Référence: 341/421

Rueda de ventilador Lama 1: 4

Référence: 341/520

Battery housing /Lama

dimensions: 7.76 x 3.4 x 5.3 cm

Référence: 31/34

Kit manches à balai

Les manches à balai et le levier de Pas font partie des équipements de base de chaque cockpit.La version illustrée correspond à ceux utilisés dans l'hélicoptère grandeur Schweizer 300 C....

Référence: 330/36

Fixation de portes

If you don't want that the doors of the Lama canopy close itself after opening, you use these magnet latches.

Référence: 30/50

Extincteur, longueur env. 70 mm

Fire extinguishers in the cockpit are mandatory for any scale model helicopter, since the full-size machines are also required to carry them.Our fire extinguisher is available in two different sizes, and it can be mounted in the cockpit in a wide variety of positions.For models up to 2000 mm rotor diameter we recommend the smaller version; the bigger one...

Référence: 340/13

Transmission factice

This dummy power unit can be installed on turbine powered helicopters to produce an even more realistic intersection between the turbine and the gearbox.When the imitation rotor brake of the dummy part is pushed over the turbine starter, the rubber connector is spring-loaded in front of the gearbox connection; retaining screws are not required.Dummy power...

Référence: 1/21

Casque pour Pilote William 1:4

As you would expect, we can also supply the matching type of GRP helmet for William the Pilot; it is simply pushed into place on his head. If you wish to fit a radio headpiece, you now have plenty of scope for your imagination: a piece of foam rubber, a thin wire mount and a coiled cable are all you need to make this accessory, and the pilot will...

Référence: 341/419

Poulies de cables Lama x6 1:4

1,18 x 3,15 x 0,72 cmPack of 6

Référence: 340/2

Accessoires maquette pour Lama turbine

The suckering ducts are on the model exactly on the same place as the original ones in position to the turbine on the full-size helicopter.

Référence: 340/29

Cockpit for Lama, turbine version

Référence: 330/10

Housse de protection pour Lama

This protective sheath provides effective protection to the cabin of your valuable helicopter, and helps to avoid unsightly scratches. It is simply pulled over the cabin and closed with a hook -and-loop fastener.Cabin sheath for Lamamatching the cabins of the models 3300 and 3400

Référence: 340/1

Support de roue pour Lama

The Lama is a large helicopter, and the supplementary wheels which can be attached to the landing gear make it much easier to move the machine into and out of the hangar. However, the wheels are removed prior to flying the model. These wheel holders for our model of the Lama are made of plastic and are simply glued to the 20 mm Ø skid tubes using UHU...

Référence: 340/5

Protection contre l'enlisement pour Lama

When full-size helicopters have to land in deep snow, the skids are fitted with "snowboards" to prevent them sinking in.On the model they look really good, and also help the pilot detect the model's orientation in the air.Make your model an eye-catcher and use some rivets for the decoration of the skies."Snowboards" for Lama, 1 pair

Référence: 330/5

Kit accessoires portes Bell 47 G III, Lama

Door fittings for large-scale model helicopters do not differ fundamentally from one type to another. However, the size of these accessories is important if the model is to look convincing, otherwise they will look out of scale.Compare the door handle of the Lama with that of the Alouette II, and the difference is obvious.The door fittings set for the...

Référence: 330/31

Fenêtre à bulle

Bubble window for Lama Ord.No. 3300 / 3400 / 3401, Rotor ø 2500 mm