Home
Brands

No brand

Suppliers
Best Sellers
Flanged ballrace 6 x 10 x 3 mm Quick view

Reference: 92/91

Flanged ballrace 6 x 10 x 3 mm

Review(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Price 14.70€
More
On sale upon request
All best sellers

There are 420 products.

Sort by:
Relevance Name, A to Z Name, Z to A Price, low to high Price, high to low
Showing 97-108 of 420 item(s)

Active filters

Silencer system UH-1D Benzin Quick view

Reference: 116/85

Silencer system UH-1D Benzin

Review(s): 0

 Silencer systemIntake pipe 55 mmSilencer chamber 170 mmOverall Ø 50 mmManifold: 34 mm hole spacingTail pipe length 130 mmWeight approx. 390 g

Price 451.60€
More
On sale upon request
Swashplate guide Quick view

Reference: 52/20

Swashplate guide

Review(s): 0

The swashplate guide prevents the outer ring of the swashplate rotating; the swashplate pin runs in the slot in this guide. The part is fixed to the dome plate using M 3 socket-head cap screws. The length of the swashplate guide slot allows generous collective pitch travels to be exploited to the full; its position on the rotor shaft can be adjusted to...

Price 14.70€
More
On sale upon request
Kevlartank for Kerosene 1.4 l Quick view

Reference: 26/50

Kevlartank for Kerosene 1.4 l

Review(s): 0

Aramid is a fibre that is used in motor racing. The tanks have an even surface inside and rough on the outside. These fuel tanks are all pressure tested to make sure that they are 100% leak-proof when they arrive at your workshop. They fit in every fuselage, that would normally use the plastic tank Ord.No. 26/5 for. For example, this Aramid tank is...

Price 349.10€
More
On sale upon request
Motor mount drilled for... Quick view

Reference: 59/2

Motor mount drilled for Rossi 11.5 cc

Review(s): 0

Factory-drilled motor mounts, already drilled and tapped for M 3 or M 4, are available in pairs (left / right). Avoid interchanging the left hand with the right hand one!1 pairfactory-drilled

Price 54.60€
More
On sale upon request
Toothed belt clutch 23-tooth Quick view

Reference: 833/64

Toothed belt clutch 23-tooth

Review(s): 0

Toothed belt clutchincl. flywheel and split taper collet23-toothpitch 3Mmaterial: aluminiumtwin ballracedincl. clutch liningfits the glow plug motorfor engines up to max. 8.5 cc onlyfits the Sky Dragon model

Price 99.90€
More
On sale upon request
Shim spacer set Quick view

Reference: 59/20

Shim spacer set

Review(s): 0

To obtain the optimum clearance between clutch pinion and main gear you can use these shim spacers, which are 0.1 and 0.2 mm thick. Simply loosen the engine retaining screws and place the appropriate shim spacer between engine and engine mount; suits all types of engine.Engine spacer set2 each 0.1 mm and 0.2 mm thick

Price 11.20€
More
On sale upon request
Exhaust for Bell 212 Twin Jet Quick view

Reference: 214/16

Exhaust for Bell 212 Twin Jet

Review(s): 0

Exhaust tubes for turbines are always designed for the specified model. It is important that no forward thrust emerges from the system. Should this still occur, the forward thrust produced is minimal.Turbine exhaust tubes are designed as exhaust-gas diffusers, i.e. opens wider towards the rear.

Price 552.50€
More
On sale upon request
Back to top

Follow us on Facebook

Facebook