Home
Brands

No brand

Suppliers
Best Sellers
Flanged ballrace 6 x 10 x 3 mm Quick view

Reference: 92/91

Flanged ballrace 6 x 10 x 3 mm

Review(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Price 14.70€
More
On sale upon request
All best sellers

There are 420 products.

Sort by:
Relevance Name, A to Z Name, Z to A Price, low to high Price, high to low
Showing 145-156 of 420 item(s)

Active filters

PTFE tape 0.1 mm Quick view

Reference: 115/12

PTFE tape 0.1 mm

Review(s): 0

To seal a fuel tank unscrew the cap and wrap 3 - 4 layers of PTFE tape round the threaded section. Screw the cap back on the tank as far as it will go.PTFE tape 0.1 mm12 mm wide, 12 m long

Price 11.20€
More
On sale upon request
PTFE pipe 20 x 2.5 x 120 mm Quick view

Reference: 115/5

PTFE pipe 20 x 2.5 x 120 mm

Review(s): 0

Manifolds and tuned pipes or silencers must be installed without touching each other, because the contact of these metal parts could cause radio interference. We can refer to this interference as "electric noise". The connection by PTFE pipe enables the required distance of 10 - 15 mm in the prescribed position, and it steadily seals gas-tight. This...

Price 19.40€
More
On sale upon request
Kerosene refuelling system Quick view

Reference: 13/32

Kerosene refuelling system

Review(s): 0

The kerosene refuelling system is sealed with a rubber nipple. The constant low pressure inside the tank draws the nipple firmly against the refuelling opening. That is also the reason why a mechanism such as a spring-controlled valve is not suitable, because the low pressure tends to push the spring back as spring tension diminishes.

Price 46.10€
More
On sale upon request
Tuned pipe silencer Quick view

Reference: 116/71

Tuned pipe silencer

Review(s): 0

 Tuned pipe silenceroverall length 400 mmconnection-Ø 20 mmoverall Ø 40 mmsilencer chamber 240 mmweight approx. 180 gtail pipe length 100 mm

Price 176.40€
More
On sale upon request
lining 45 x 40 x 12 mm Quick view

Reference: 64/8

lining 45 x 40 x 12 mm

Review(s): 0

Friction between the flywheel and the clutch bell result in a certain amount of wear of the clutch lining.For installation you slightly grind one of the outer edges. Afterwards you press the liner with that edge in front into the clutch bell. To glue in a new clutch liner you use e.g. UHU plus endfest 300, Ord.No. 10/26 or 10/27.Fits the glow plug motor...

Price 27.40€
More
On sale upon request
Swashplate driver 10 mm Quick view

Reference: 68/20

Swashplate driver 10 mm

Review(s): 0

Where a pitch compensator sits and two pushrods connect to the flybar, this is now a swashplate driver in its place.This is necessary to drive the inner ring of the swashplate in order to always control the blade angle in the same position.Aluminium swashplate driver with 4 ballraces.

Price 87.20€
More
On sale upon request
Cooling fan for petrol engine Quick view

Reference: 830/67

Cooling fan for petrol engine

Review(s): 0

This additional fan supports the cooling system of the petrol engine and at the same time the air is drawn constantly out of the fuselage.

Price 30.60€
More
On sale upon request
Exhaust for XL-C Quick view

Reference: 268/16

Exhaust for XL-C

Review(s): 0

Exhaust tubes for turbines are always designed for the specified model. It is important that no forward thrust emerges from the system. Should this still occur, the forward thrust produced is minimal.Turbine exhaust tubes are designed as exhaust-gas diffusers, i.e. opens wider towards the rear.

Price 254.50€
More
On sale upon request
Back to top

Follow us on Facebook

Facebook