Home

Filter By

Availability

Availability

Price

Price

  • 5.00€ - 55.00€

Categories

Categories

Brands

No brand

Suppliers
Best Sellers
Flanged ballrace 6 x 10 x 3 mm Quick view

Reference: 92/91

Flanged ballrace 6 x 10 x 3 mm

Review(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Price 14.70€
More
On sale upon request
All best sellers

There are 59 products.

Sort by:
Relevance Name, A to Z Name, Z to A Price, low to high Price, high to low
Showing 37-48 of 59 item(s)

Active filters

  • Categories: Drill Bits & Taps
  • Categories: Pliers & Cutters
  • Categories: Specific Aids
Soft sanding paper Quick view

Reference: 11/65

Soft sanding paper

Review(s): 0

For preparing the GRP surface prior to the paintingP400dimensions: 11.5 x 15 cmPack of 5

Price 9.70€
More
On sale upon request
Twist drill 3.2 mm Quick view

Reference: 11/88

Twist drill 3.2 mm

Review(s): 0

When screwing together parts in the mechanics (direct linkage) Allen screws are preferable to normal screws; use M 2.5 for Futaba servos and M 3 for Graupner / JR servos. We supply all required sizes of drills and taps for the work on your model helicopter.

Price 5.50€
More
On sale upon request
Pipe bending tool Quick view

Reference: 11/80

Pipe bending tool

Review(s): 0

A versatile bending tool for fuel tank pipes, dummy collective pitch sticks in the cockpit etc. The tool is useful for tubes or pushrods with a diameter of 3.0 and 3.2 mm

Price 44.30€
More
On sale upon request
Twist drill 4.0 mm Quick view

Reference: 11/89

Twist drill 4.0 mm

Review(s): 0

We supply all required sizes of drills and taps for the work on your model helicopter.

Price 5.50€
More
On sale upon request
Pushrod measuring holder Quick view

Reference: 11/86

Pushrod measuring holder

Review(s): 0

Model helicopter building instructions always state pushrod length as measured from ball centre to ball centre.Determining this dimension using conventional measuring tools is not really much more accurate than estimating the length.Pushrod measuring holderpack of 2holders fit any standard calipers

Price 14.80€
More
On sale upon request
Twist drill 1.2 mm Quick view

Reference: 11/96

Twist drill 1.2 mm

Review(s): 0

We supply all required sizes of drills and taps for the work on your model helicopter.

Price 5.50€
More
On sale upon request
Three-armed gripper Quick view

Reference: 9/11

Three-armed gripper

Review(s): 0

This handy three-armed gripper acts as a finger-extension for placing screws and nuts in difficult, small and inaccessible places.  Three-armed grippertotal length 115 mm

Price 11.70€
More
On sale upon request
Twist drill 5.0 mm Quick view

Reference: 11/97

Twist drill 5.0 mm

Review(s): 0

We supply all required sizes of drills and taps for the work on your model helicopter.

Price 5.50€
More
On sale upon request
Die M 2.5 HSS Quick view

Reference: 70/20

Die M 2.5 HSS

Review(s): 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Price 46.10€
More
On sale upon request
Ratchet tool holder Quick view

Reference: 90/5

Ratchet tool holder

Review(s): 0

When you need a threaded hole in a workpiece, you just drill a core hole, then drive a tap into it to cut the thread. The best method of thread-cutting by hand is to use a ratchet tool holder, as this gives you the best chance of keeping the thread "straight". The ratchet can be switched to right-hand and left-hand locking, plus a rigid (no ratchet)...

Price 37.80€
More
On sale upon request
Back to top

Follow us on Facebook

Facebook