H145 (EC145) 1:6 - Fuselage kit

Reference: 40/3

Skid tube 15 mm

Skid tubes for model helicopters powered by combustion engines are made of aluminium with a wall thickness of 1 mm.Specification 15 mm ØOverall length approx. 530 mmContent of the package 1 piece

Reference: 3310

Electric motor set for X-Treme mechanics

For the conversion of Xtreme mechanics to electric, for 10 S LiPos (LiPos are not included in the set). Supplied with the drive set are: electric motor, controller, programmer, motor mount, pulley, belt, fixings Due to constantly changing supply and availability of electric motors, the motor used in this set may vary. Currently, the Pyro 700-52 from...

Reference: 3310/12

Electric motor set for X-Treme mechanics 12S

For the conversion of Xtreme mechanics to electric, for 12 S Lipos. (LiPos are not included in the set)Supplied with the drive set are: electric motor, controller, programmer, motor mount, pulley, belt, fixingsDue to constantly changing supply and availability of electric motors, the motor used in this set may vary. Currently, the Pyro 700-45 from...

Reference: 35/37

Rotor shaft 10 x 235 mm

 Rotor shaftfor multi-blade headhole spacing 35 mm

Reference: 35/40

Rotor shaft 10 x 194 mm

 Rotor shaftfor multi-blade headhole spacing 35 mm

Reference: 26/100

Benzin kit incl. fuel tank 540 ccm

Not available

Reference: 26/5

Tank for Kerosene 1.25 l

Tank for Kerosene, 1250 ml, 2 x required for the Lama

Reference: 26/50

Kevlartank for Kerosene 1.4 l

Aramid is a fibre that is used in motor racing. The tanks have an even surface inside and rough on the outside. These fuel tanks are all pressure tested to make sure that they are 100% leak-proof when they arrive at your workshop. They fit in every fuselage, that would normally use the plastic tank Ord.No. 26/5 for. For example, this Aramid tank is...

Reference: 830/68

Fine-mesh petrol and kerosine filter

Chemical analysis used in Formel 1 is able to determine 1 g of impurity within 1 ton of oil. To fulfill your demand on the cleanness of the fuel for your model helicopter you use the fine-mesh petrol filter inside the fuel tubing between the tank and the carburettor. Also suitable for kerosine turbine fuel.

Reference: 830/83

Petrol fuel tubing 1 m

Fuel tubing for petrolapprox. 1 mtransparentFuel tubing inevitably suffers from the effects of ageing. Always replace brittle tubing before it gives problems! 

Reference: 704/30

4-blade rotor head 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 704/32

4-blade rotor head 12 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 404/41

4-blade-set 1680 mm

Specification4-blade-setlength: 765 mmrotor disc: 1680 mmblade root: 14 mm 2-holeblade chord: 53 mmprofile thickness: 6.8 mmweight: ca. 185 gmaterial: CFRPShark Skin finish: anthracite mattsymmetry: reflex l.h.r.

Reference: 107/49

Ball-links 3.0 mm

Pack of 25

Reference: 133/5

Door fittings set EC 135 & EC145

Door fittings set EC 135 & EC145

Reference: 145/29

Cockpit EC 145

Cockpit including scale accessories (Ord.No. 29/2), without pilot and without scale accessory. To further build up the interior with joy sticks etc. please refer to our suggested accessories.

Reference: 133/10

Skid landing gear for EC 135

 Skid landing gear for EC 135original kit accessoriescomplete as shown

Reference: 1002/21

Petrol mechanics 90:18

Reference: 830/101

Electric Benzin Conversion Kit, 6mm shaft

Benzin-Trainer to electric conversion?..why not! Here is a rather simple way to convert your Benzin Trainer to electric power. Remove the Petrol motor and exhaust and replace it with an electric motor of your choice. The motor mount retrofit set can be used with the most common electric motors. This conversion set can also be used with the Benzin fuselage...

Reference: 1002/4

Mechanics set X-Treme

Not available

Reference: 1002/80

Electric mechanics, excl. motor, 10 mm mainshaft

Reference: 53/16

Dome fittings set for PHT3 45 degree

Bell cranks/main shaft adaptor for JetCat Turbine. For 4-blade main rotor head.

Reference: 116/95

Silencer system

 Silencer systemIntake pipe 170 mmSilencer chamber 195 mmOverall Ø 50 mmManifold: 34 mm hole spacingTail pipe length 80 mmWeight approx. 390 g

Reference: 1022/13

Carburettor intake trumpet

This screw-fitting carburettor intake trumpet is designed to improve the flow of air entering the carburettor. Complete with screws and gasket.

Reference: 4321

Suppressed plug cap for petrol engine G230 / G240

Suppressed plug cap to protect the radio control system from potential interference caused by the ignition system

Reference: KEROSTART

Kerosene start for JetCat

Kero Start SystemWorks with a standard 2S LiPo battery.Minimal power requirement of only 50 watts!Backward compatible with all JetCat engines.No change in the wiring necessary.Screw out the glow plug & screw in the kerosene starter system, insert the previous gas valve into the kerosene circle, and you're done!All ECU`s from version 4.00 can be...

Reference: PHT3-SERVOPLATTEN

Servo mounting frames for PHT3

Pack of 2

Reference: 144/16

Exhaust for EC 145 Turbine

stainless steelfor turbine 

Reference: 68/50

Swashplate driver 12 mm

 Swashplate driver, metal4 ballracesweigth approx. 25.8 gsuitable for 12 mm Ø main shafts

Reference: 68/20

Swashplate driver 10 mm

Where a pitch compensator sits and two pushrods connect to the flybar, this is now a swashplate driver in its place.This is necessary to drive the inner ring of the swashplate in order to always control the blade angle in the same position.Aluminium swashplate driver with 4 ballraces.

Reference: 832/68

Swashplate for main shaft 12 mm

The use of a mechanics with 12 mm Ø main shaft requires a swashplate with an appropriate swivel ballrace.

Reference: 707

Rotor cap for Multi blade head

The diameter is 83 mm and the construction height from the screw-on surface to the highest point is 13 mm.It is fastened using an M4 x 14 hexagon socket screw (included).

Reference: 1003/80

2-blade tail rotor ø 6 mm aluminium

Reference: 34/30

Tail rotor blades 130 mm

Tail rotor bladesSpecification 8.0 mm blade root8.7 g approx.29 mm blade chord5.0 mm profile thicknesssymmetrical130 mm longbalanced1 pair

Reference: 49/12

Claw connector, shaft 5 mm

 Claw connector with 5 mm shaftlength of the steel shaft 22 mm

Reference: 134/617

Cover for sliding door 1:6

dimensions: 8 x 1.4 x 0.8 cmPack of 2

Reference: 134/609

Antenna EC145 1:6

dimensions: 3.1 x 1.2 x 1.2 cmincl. wire

Reference: 134/611

Antenna, round, 1:6

dimensions: diameter: 4.5 cm, height: 1.7 cm

Reference: 134/627

Rear antenna x2 1:6

dimensions: 0.93 x 0.88 x 2.37 cmPack of 2incl. wire

Reference: 134/695

Fenestron antenna 1:6

dimensions: 5.13 x 0.6 x 0.95 cmincl. wire

Reference: 134/636

Curved antenna 1:6

dimensions: 8.4 x 1.4 x 4.2 cm

Reference: 134/649

Pitot tube 1:6

dimensions: 2.25 x 1 x 1.59 cm

Reference: 134/651

Fix x2 for winch 1:6

dimensions: 4.78 x 1.02 x 0.89 cmPack of 2

Reference: 134/602

Cyclic & collective control x2 1:6

dimensions: 10 x 2.5 x 1.9 cmPack of 2 (each 2-part) (l/r)

Reference: 144/629

Detailed Cockpit EC145 1:6

Not available

Reference: 134/608

Pedals EC x2 1:6

dimensions: 5.6 x 4 x 2.55 cmPack of 2

Reference: 134/639

Collective Pitch lever x2 1:6

dimensions: 3.7 x 1.37 x 7 cmPack of 2

Reference: 134/616

Thermal imaging camera 1:6

Not available

Reference: 134/619

Headlight x2 1:6

dimensions: diameter: 2.4 cm, height: 2.3 cmPack of 2

Reference: 134/643

Distress beacon 1:6

dimensions: 5.3 x 1.4 x 1.23 cm

Reference: 134/670

Scale decals EC 135/145 1:6

scale 1:6

Reference: 134/607

Front & back air intake "Naza duct", EC x2 1:6

big: dimensions: 4.1 x 3.06 x 0.63 cmPack of 2small: dimensions: 2.6 x 1.33 x 0.45 cmPack of 2

Reference: 134/604

Air inlets 1:6

dimensions: 2.3 x 2.2 x 0.85 cmPack of 6

Reference: 134/635

Vents 1:6

dimensions:part 1: 6 x 2.5 x 0.2 cmpart 2: 5.65 x 3.43 x 0.2 cmpart 3: 3.53 x 2.53 x 0.2 cmPack of 3 x 2

Reference: 134/605

Air inlets x2 1:6

dimensions: 5 x 4.2 x 0.3 cmPack of 2

Reference: 134/606

Air inlet 1:6

dimensions: 3 x 2.75 x 0.7 cm

Reference: 134/647

Air grill x2 1:6

dimensions: 4.1 x 3 x 0.2 cmPack of 2

Reference: 134/631

Triangular step rail, bent, EC, 1:6

length: approx. 50 cm

Reference: 134/630

Triangular step rail, straight, EC, 1:6

length: approx. 50 cm

Reference: 134/625

Door hardware x8 1:6

dimensions: 2 x 1.64 x 0.53 cm Pack of 8  

Reference: 134/644

Winch connections 1:6

flat: dimensions: 1.52 x 1.52 x 0.7 cmPack of 3high: dimensions: 1.29 x 1.29 x 1.15 cmPack of 4

Reference: 134/646

Speaker 1:6

dimensions: 7 x 4.7 x 2.8 cm

Reference: 3173

controller for winch motor

Not available

Reference: 1/70

Pilot Joe, 1:7, white long sleeve + jeans

Pilot Joe 240mm Scale 1:7 white long sleeve + jeans   Made in Germany

Reference: 1/79

Pilot Joe 1:7, long sleeve + trousers

Pilot Joe 240 mm Scale 1:7 long sleeve + trousers Made in Germany

Reference: 995

RC system accessories incl. 5 servos

If you already own a radio control system and then purchase a second model helicopter, the next step is to consider carefully which electronic components are the best choice for the new model.The combination illustrated here comprises accessories which have proved excellent in practice. RC system accessories, with Futaba BLS 452 servos excluding radio...

Reference: 33/4

Rotor bolsa de cuchillas 4 cuchillas Ø 2500 mm

Reference: 70/50-4

Varilla de empuje 2.5 x 50 mm

Reference: 133/22

Cono de nariz de radar, GRP

Reference: 145/30

Juego de acristalamiento EC 145

Reference: 871/100

Umbauset für X-Treme Elektro-Mechanik

Reference: 70/70-4

Gestänge 2,5 x 70 mmOrd.No. 70/70-4

Reference: 70/101-4

Gestänge 3,0 x 100 mmOrd.No. 70/101-4

Reference: 133/9

Kufenbügel 12 mm