Robinson R22 1:4 - Fuselage kit

Reference: 722/0

Decal sheet Robinson R22

Stickers with type specific lettering, registration, and warning notices are printed on clear foil. With ruler and scalpel (Ord.No. 11/59) you will obtain a clean cut for individual items out of a...

Reference: 722/30

Glazing set Robinson R22

  Robinson R22 glazing set smoked tint not trimmed

Reference: 3307

Electric Motor set for Benzin mechanics 12S

For the conversion of benzin mechanics to electric

Reference: 3308

Electric Motor set for Benzin mechanics 10S

For the conversion of benzin mechanics to electric

Reference: 722/35

Rotor shaft 12 x 560 mm

Not available

Reference: 26/100

Benzin kit incl. fuel tank 540 ccm

Not available

Reference: 830/68

Fine-mesh petrol and kerosine filter

Chemical analysis used in Formel 1 is able to determine 1 g of impurity within 1 ton of oil. To fulfill your demand on the cleanness of the fuel for your model helicopter you use the fine-mesh petrol filter inside the fuel tubing between the tank and the carburettor. Also suitable for kerosine turbine fuel.

Reference: 830/83

Petrol fuel tubing 1 m

Fuel tubing for petrolapprox. 1 mtransparentFuel tubing inevitably suffers from the effects of ageing. Always replace brittle tubing before it gives problems! 

Reference: 1005/49

Rotor head up to 2500 mm for Bell 230 or AIRWOLFOrd.No. 1005/49

This rotor head is specially designed for the use with an AIRWOLF or a Bell 230.Rotor shaft 12 mm, rotor disc 2360 mmOrd.No. 1005/52 is for a Ø 15 mm rotor shaft and Ord.No. 1005/49 for a Ø 12 mm rotor shaft

Reference: 722/72

Rotor head VR-22

The loading of every component of this rotor system is designed to take a multiple of the actual forces. We are looking here at purely safety reserves and under no cirumstances should they be used for experimental purposes.Because of the special requirements of materials used in the rotor head, we expressly recommend that only genuine VARIO spare parts...

Reference: 89/2

Pushrod cranked, 2.5 x 82 mm

On 2-blade rotor heads with flybar the angled pushrods connect the pitch compensator with the control bridge.Ready-made pushrod, threaded M 2.5, approx. 8 mm thread length each end. Pack of 2.

Reference: 722/11

Stabiliser set Robinson R22

 Stabiliser set, GRP3-partfor Robinson R22 with a length up to approx. 1 820 mm

Reference: 722/1

Skid landing gear for Robinson

 Skid landing gear for Robinsonoriginal kit accessoriescomplete as shown

Reference: 470/23

Petrol mechanics for Robinson R22

This mechanical system has been developed specifically for the Robinson R22, so that the model helicopter can be fitted with a VARIO G230 petrol engine.Without motor and petrol components (see Ord.No. 26/100).

Reference: 830/101

Electric Benzin Conversion Kit, 6mm shaft

Benzin-Trainer to electric conversion?..why not! Here is a rather simple way to convert your Benzin Trainer to electric power. Remove the Petrol motor and exhaust and replace it with an electric motor of your choice. The motor mount retrofit set can be used with the most common electric motors. This conversion set can also be used with the Benzin fuselage...

Reference: 722/16

Silencer system

Silencer systemIntake pipe 55 mmSilencer chamber 260 mmOverall Ø 50 mmManifold: 34 mm hole spacingTail pipe length 110 mmWeight approx. 250 g

Reference: 1022/13

Carburettor intake trumpet

This screw-fitting carburettor intake trumpet is designed to improve the flow of air entering the carburettor. Complete with screws and gasket.

Reference: 4321

Suppressed plug cap for petrol engine G230 / G240

Suppressed plug cap to protect the radio control system from potential interference caused by the ignition system

Reference: 415

2-blade-set 2160 mm

Specification 2-blade-set length: 950 mm rotor disc: 2160 mm blade root: 22 mm 1-hole blade chord: 75 mm profile thickness: 11 mm weight: ca. 400 g material: CFRP Shark Skin finish: anthracite matt symmetry: reflex l.h.r.

Reference: 33/2

Rotor blade pouch 2-blade Ø 2100 mm

bag length: 98 cmmax. blade width: 9.5 cm

Reference: 68/50

Swashplate driver 12 mm

 Swashplate driver, metal4 ballracesweigth approx. 25.8 gsuitable for 12 mm Ø main shafts

Reference: 722/71

Collective pitch compensator 12 mm

Pitch compensator, complete, for 12 mm Ø main shaft, centre piece aluminium.For use with the rotor head Ord.No. 722/72.

Reference: 34/32

Tail rotor blades 156 mm, grey

Tail rotor blade, rotor disc 390 mm ØSpecification 8.0 mm blade root16.5 g approx.45.5 mm blade chordGRP6.7 mm profile thicknesssymmetrical156 mm longbalanced1 pairThe tail rotor blades are designed exclusively for use with the specified VARIO mechanics in conjunction with the tail rotor 1003/80. The maximum rotational speed of the tail rotor shaft is...

Reference: 1/40

Pilot William, 1:4, white long sleeve + jeans

Pilot William 450 mm Scale 1:4 white long sleeve top + jeans Made in Germany

Reference: 1/49

Pilot William 1:4, green long sleeve + trousers

Pilot William 450 mm Scale 1:4 green long sleeve top + trousers Made in Germany

Reference: 995

RC system accessories incl. 5 servos

If you already own a radio control system and then purchase a second model helicopter, the next step is to consider carefully which electronic components are the best choice for the new model.The combination illustrated here comprises accessories which have proved excellent in practice. RC system accessories, with Futaba BLS 452 servos excluding radio...

Reference: 70/142-2

Gestänge 3,0 x 142 mmOrd.No. 70/142-2

Reference: 70/105-2

Gestänge 3,0 x 105 mmOrd.No. 70/105-2

Reference: 722/81

Heckausleger Robinson R22

Reference: 722/24

Gebläseschachtattrappe

Reference: 722/58

Domverkleidung R22, GFK

Reference: 722/2

Kufenrohr 15 mm Robinson