Brands

No brand

Reference: 10/90

Canopy latch

Review(s): 0

The canopy retainer set helps to keep your canopies undamaged for a long period. It absorbs movement, such as abrupt shocks in hard landings, and prevents cracks developing in the canopy.Knurled nuts are used to hold the canopy in place, and they do not intent the canopy when tightened.The components of the canopy retainer system are screwed against...

Price 6.20€
More
On sale upon request

Reference: 060

Ball-end bolt 3.5 mm - M 2.0 x 5.0

Review(s): 0

These ball-end bolts offer an optimal connection between a GRP servo output arm and the pushrod to the mechanics. Underneath the output arm you lock the ball-end bolt with an M 2 hexagon nut. For aluminium output arms you use ball-end bolts Ord.No. 060/7 and thread-lock fluid.

Price 13.80€
More
In stock
All best sellers

PTFE bush guide for 0.8 mm tailboom

800/9
Rating 

PTFE guides in the tail boom provide the necessary "lubrication" for the drive shaft, which eliminates the need to oil the system separately.

PTFE guide for 0.8 mm tail boom

Pack of 3
 

17.20€
Tax included
Quantity
On sale upon request

 

Política de seguridad

 

Política de envío

 

Política de devolución

Description

PTFE guides in the tail boom provide the necessary "lubrication" for the drive shaft, which eliminates the need to oil the system separately.

PTFE guide for 0.8 mm tail boom

Pack of 3
 

Product Details
800/9
Reviews

No customer reviews for the moment.

Write your review

PTFE bush guide for 0.8 mm tailboom

PTFE bush guide for 0.8 mm tailboom

PTFE guides in the tail boom provide the necessary "lubrication" for the drive shaft, which eliminates the need to oil the system separately.

PTFE guide for 0.8 mm tail boom

Pack of 3
 

Write your review
16 other products in the same category:

Reference: 17

Tail rotor shaft 2 mm

Review(s): 0

The 2 mm steel tail rotor shaft has proved its worth for several decades, especially in beginners' models.Drive shaft, steel, 2.0 x 980 mm

Price 5.60€
More
On sale upon request

Reference: 17/10

Stainless steel tail drive system

Review(s): 0

When a 2 mm steel drive wire is used between main gearbox and tail gearbox the tail rotor might yaw the heli during acrobatics (e.g. turn), because the wire might "wind up". At this moment a small "wind up" will cause a small change of tail rpm, which requires steering corrections.A so-called "rigid" tail drive system gives a more exact drive to the tail...

Price 73.00€
More
On sale upon request

Reference: 17/7

Articulated centre support

Review(s): 0

The use of an articulated centre support in helicopters with extreme high mounted tail booms (e.g. Hughes 500) helps to balance up to 30 mm vertical off-set between mechanics and tail rotor. The centre support is double ballraced and pre-assembled.

Price 67.70€
More
On sale upon request

Reference: 17/16

Stainless steel tube 6.0 x 0.3 x 950 mm

Review(s): 0

Advanced pilots appreciate the more precise control response of a rigid tail rotor drive system, as provided by a stainless steel drive shaft. Stainless steel tube 6.0 x 0.3 x 950 mm

Price 30.00€
More
On sale upon request

Reference: 17/14

Stainless steel tail drive system for 20 mm

Review(s): 0

Of course the explanation of Ord.No. 17/10 concerning a 2 mm steel drive wire in acrobatics applies not only for fuselages, it is similar for training helicopters.When you convert a trainer you use the existing tail boom. Main gearbox and tail gearbox have to be provided with a claw connector 49/12 each.Models over a certain age should be checked whether...

Price 88.90€
More
On sale upon request

Reference: 17/13

Articulated joint tail drive system

Review(s): 0

On a model helicopter like the Hughes 500 e.g. the tail boom is extremely high connected. Therefore an articulated centre support is applied in addition to the articulated tail drive system. The centre support is double ballraced and pre-assembled.Articulated joint tail drive systemwith articulated centre support

Price 138.60€
More
On sale upon request